Basement Watchdog Special - Manual (Page 3)

Introduction
The Basement Watchdog Special backup sump
pump system is battery-operated. It is designed
as an emergency backup system to support your
main AC sump pump, and it will automatically
begin pumping any time the float switch is
activated by rising water. Should any
malfunction or emergency occur that involves
the sump pump, the battery, or the AC power,
the Basement Watchdog system will sound an
alarm. A light on the display panel of the
control unit will indicate the cause of the alarm
and the corrective action.
For added reliability, the float switch has, not
one, but two floats. Should one float fail to
operate, the second float automatically activates
the pump.
The Basement Watchdog Special Sump Pump
System includes:
• A control unit with a dual float switch, a
battery fluid level sensor, battery cables, and a
20 amp fuse
• A pump with a 1½” PVC pipe adapter
• A plastic wire tie for mounting the float switch
• A battery box
• A battery charger
• A battery cap with a hole to accommodate the
fluid sensor
You will also need to supply:
• A Basement Watchdog 7.5 Hour Standby
Battery *
DO NOT use an automotive battery with this
system
DO NOT use a Basement Watchdog Emergency
battery with this system. It will not run the
pump as long as the 7.5 hour battery
• 1½” rigid PVC pipe and fittings
• PVC primer and cement
• A union with hose clamps or a “Y” connector
and two (2) check valves, depending on the
installation method you use
• A surge protector (recommended)
• Six (6) quarts of 1.265 specific gravity battery
acid
*Basement Watchdog standby batteries are
specifically designed to work with your
battery backup sump pump system.
Glentronics
can not guarantee the
compatibility of other brands of batteries. For
optimal performance the use of a Basement
Watchdog standby battery is recommended.
For narrow sump pits you will need some
additional parts:
• An “L” bracket at least six (6) inches long
(preferably one that will not rust)
• Two (2) stainless steel hose clamps
• One (1) stainless steel screw (#8-32 x 3/4”), a
matching washer & nut
Use of a Basement
Watchdog Klunkless
Check Valve™ will
provide quieter
operation. (See
page 18 for more
information.)
Replacement Part Numbers
Pump . . . . . . . . . . . . . . . . . . . . . . .1011002
Float switch assembly . . . . . . . . . . . .1020009
Fluid sensor assembly . . . . . . . . . . . .1014001
Pipe adapter . . . . . . . . . . . . . . . . . .1120002
Charger . . . . . . . . . . . . . . . . . . . . . .1015001
Battery box . . . . . . . . . . . . . . . . . . .1113003
Battery cap with hole . . . . . . . . . . . .1125000
Call 800-991-0466, option #3 to order parts.
System Specifications
Power supply requirements . . . . . .115 volts AC
Pumping capacity . . . . . . . . . .2500 GPH @ 0’
Pumping capacity . . . . . . . . .1730 GPH @ 10'
Pump dimensions w/elbow . . . . . .7
5 ⁄
8
” H x 9”W
Pump housing & strainer . . . . . .non-corrosive,
will not rust
Pump . . .can run dry for short periods of time;
can be used in sumps with water softener
Float switch . . . . . . . . . .independent, can be
set at any level
Page 2
Battery
Wires
Control Unit
Battery
Box
Charger
Cap
Wire Tie
Float
Switch
Pipe
Adapter
Pump
Fluid Sensor