Great Plains 2510HDF Parts Manual - Manual (Page 73)

Revision Comments Part Description Part No. Ref.
Image No. dwg27121
MARKER MOUNT RH 113-690H 1.
Shown MARKER MOUNT LH 113-689H 1.
FIRST PIVOT SHAFT 113-312D 2.
BUSHING CYL 1 1/4 X 1 X 1 890-005C 3.
GREASE ZERK STRAIGHT 1/4-28 800-001C 4.
RH FIRST SECTION 113-188H 5.
Shown LH FIRST SECTION 113-180H 5.
NUT LOCK 3/8-16 PLT 803-013C 6.
LIFT LUG CHANNEL R.H. 113-467H 7.
Shown LIFT LUG CHANNEL L.H. 113-468H 7.
SECOND PIVOT SHAFT 113-313D 8.
WASHER FLAT 1 SAE 804-029C 9.
PIN 1 OD X 4.41 USABLE 113-248D 10.
PIN COTTER 3/16 X 2 805-058C 11.
HHCS 1/2-13X4 1/2 GR5 SPTHD 802-249C 12.
NUT LOCK 1/2-13 PLT 803-019C 13.
HHCS 3/8-16X1 3/4 GR2 802-253C 14.
CYLINDER STOP 113-324D 15.
STOP BUSHING 113-325D 16.
116-063HER BREAKAWAY 113-646H 17.
WASHER FLAT 1/2 USS PLT 804-017C 18.
13' MARKER TUBE 46 1/2 LONG 113-354D 19.
MARKER DISC & HUB ASSEMBLY 113-563S 20.
Refer to Hydraulic Cylinder 2 x 20 x
1.12 (810-205C) for breakdown
CYL 2X20X1.12 ROD (TIE) 1 PIN 810-205C 21.
NUT LOCK 5/8-11 PLT 803-024C 22.
HHCS 5/8-11X5 1/2 GR5 802-254C 23.
HHCS 5/16-18X2 GR5 802-115C 24.
NUT LOCK 5/16-18 PLT 803-011C 25.
HHCS 1/2-13X3 1/4 GR5 802-099C 26.
SCREW SET SQ HD 1/2-13X1 GR5 801-054C 27.
NUT HEX JAM 1/2-13 PLT 803-036C 28.
NUT HEX 1/2-13 PLT 803-020C 29.
WASHER LOCK SPRING 1/2 PLT 804-015C 30.
ADJUST MOUNT SPACER TUBE 113-491D 31.
MARKER DISK ADJUST MOUNT 113-503H 32.
U-BOLT 5/8-11 X 7 1/32 X 6 1/2 806-053C 33.
U-BOLT 1/2-13 X 3 1/32 X 6 806-122C 34.
WASHER FLAT 5/8 SAE PLT 804-021C 35.
WASHER LOCK SPRING 5/8 PLT 804-022C 36.
NUT HEX 5/8-11 PLT 803-021C 37.
NUT HEX 1/2-13 PLT 803-020C 38.
DECAL REFLECTOR AMBER 1 1/2X9 838-265C 39.
DECAL WARNING PINCH/CRUSH MRKR 818-682C 40.
11/20/12 - 73 - 288-340P
Table of Contents Part Number Index
Marker
Flat Fold Marker 25FT
(Applies to 1510HDF, 2010HDF, 2510HDF only)