Great Plains 2510HDF Parts Manual - Manual (Page 51)

Revision Comments Part Description Part No. Ref.
Image No. dwg24327
TUBE RND 1 OD X 7/32W X 3.31 120-245D 1.
TUBE RND 1 OD X 7/32W X 3.31 120-313D 2.
SPACER TUBE 1 ID X 1.25 120-315D 3.
SPKT 40C14 X 7/8 HEX BORE 120-339H 4.
GW UPPER FRNT 7/8 HEX SHFT 15P 120-340H 5.
SHAFT 7/8 HEX GW SPEED CHANGE 120-351D 6.
SPKT 40C60 X 7/8 HEX BORE 195-172H 7.
DOUBLE SPOOL IDLER ASSY 402-140S 8.
IDLER BOLT PLATE 402-242D 9.
RHSNB 5/16-18X1 1/4 GR5 802-009C 10.
HHCS 1/2-13X4 3/4 GR5 802-201C 11.
RHSNB 3/8-16X1 3/4 GR5 802-252C 12.
NUT HEX 1/2-13 PLT 803-020C 13.
803-184 FLG TP LK 5/16-18ZNYCR 803-177C 14.
NUT FLANGE LOCK 3/8-16 PLT 803-209C 15.
WASHER LOCK SPRING 1/2 PLT 804-015C 16.
WASHER MACH 1.50 X 1.00 X 18GA 804-061C 17.
WASHER FLAT 1/2 USS HARD PLT 804-113C 18.
PIN ROLL 1/4 X 1 1/2 LG PLT 805-180C 19.
PIN LINCH 3/16 X 1 9/16 LONG 805-240C 20.
SPKT 40C15 X 7/8 HEX BORE 808-147C 21.
SPKT 40C24 X 7/8 HEX BORE 808-151C 22.
SPKT 40C44 X 7/8 HEX BORE 808-225C 23.
SPKT 40C36 X 7/8 HEX BORE 808-251C 24.
IDLER 1 PC 2.38X1.01X1.062 817-406C 25.
BRG 7/8HEXX2.05OD SPH 822-119C 26.
FLANGETTE 52 3-BOLT PLT 822-175C 27.
CHAIN RL #40 84 PITCHES 136-023D 28.
CHAIN RL #40 112 PITCHES 136-136D 29.
OFFSET DOUBLE IDLER WELDMENT 402-126H 30.
TUBE RND 1 OD X 7/32W X 1.56 120-305D 31.
IDLER 1 PC 2.38X1.01X1.062 817-406C 32.
WASHER FLAT 1/2 USS PLT 804-017C 33.
PIN COTTER 7/64 X 1 LONG 805-064C 34.
FEEDER CUP DRIVE BRACKET LH 117-037D 35.
FEEDER CUP DRIVE BRACKET RH 117-038D 35.
U-BOLT 3/8-16 X 5 1/32 X 4 1/4 806-165C 36.
WASHER FLAT 3/8 USS PLT 804-011C 37.
WASHER LOCK SPRING 3/8 PLT 804-013C 38.
NUT HEX 3/8-16 PLT 803-014C 39.
RHSNB 5/16-18X3/4 GR5 802-092C 40.
SPKT 40B12 7/8 HEX BORE W/SS 808-143C 41.
CHAIN RL #40 125 PITCHES 136-033D 42.
TUBE RND DOM. 1 OD X 7/32WX3.0 120-293D 43.
HHCS 1/2-13X4 1/4 GR5 802-311C 44.
11/20/12 - 51 - 288-340P
Table of Contents Part Number Index
Drive
Dual Gauge Wheel Transmission 20FT & 25FT
(Applies to 1510HDF, 2010HDF, 2510HDF only)