Table of contents part number index, Disk gang assembly, 7 1/2" & 9" spacing – Great Plains 4336 DH Parts Manual User Manual
Page 79
Revision
Comments
Part Description
Part No.
Ref.
Image No.
dwg 41339
Located on right front & left rear of
disk.
C-SHANK HANGER 1.25X2.50 RH
807-263C
1.
(shown) Located on left front & right
rear of disk.
C-SHANK HANGER 1.25X2.50 LH
807-264C
1.
C-SHANK PLATE, TOP
556-064H
2.
Rev. 1
Located on right front & left rear of
disk.
SCRAPER BRACKET, SPRING RH
556-233H
3.
Replaced by 566-233H.
SCRAPER BRACKET, SPRING RH
556-346D
3.
Rev. 1
(shown) Located on left front & right
rear of disk.
SCRAPER BRACKET, SPRING LH
556-234H
3.
Replaced by 566-234H.
SCRAPER BRACKET, SPRING LH
556-347D
3.
ZERK GREASE STRAIGHT 1/8-27MPT
800-130C
4.
BRG INS 1.78ID CDS211TTR23N
822-026C
5.
CASTING TOP BEARING
812-006CP
6.
Rev. 2
(S/N A1323P+)
CASTING CAP BOTTOM
812-059C
7.
Rev. 1
Replaced by 812-059C (S/N A1322P-)
CASTING BOTTOM BEARING FINISHD
586-187D
7.
Rev. 1
BEARING SHIELD
556-375D
8.
9" disc spacing (shown)
HALF SPOOL LONG, 9
556-124D
9.
7 1/2" disc spacing
HALF SPOOL LONG, 7 1/2
556-123D
9.
HALF SPOOL DISK, SHORT
556-122D
10.
9" disc spacing
FULL SPOOL DISK, 9
556-121D
11.
7 1/2" disc spacing
FULL SPOOL DISK, 7 1/2
556-120D
11.
(shown)
BLADE DISC 24RC .197X1.78 HOLE
820-355C
12.
Rev. 2
Replaced by 820-446C (S/N A1461P-)
BLADE DISC 24RC X.256 ROLLABLE
820-446C
12.
Rev. 1
Replaced by 820-446C (S/N A1462P+)
BLADE DISC 24RC .256X1.78 HOLE
820-356C
12.
BLADE DISC 22RC .197X1.78 HOLE
820-357C
12.
Rev. 2
Replaced by 820-446C (S/N A1461P-)
BLADE DISC 22RC X.256 ROLLABLE
820-445C
12.
Rev. 1
Replaced by 820-446C (S/N A1462P+)
BLADE DISC 22RC .256X1.78 HOLE
820-358C
12.
BLADE DISC 20RC .197X1.78 HOLE
820-359C
12.
Rev. 2
Replaced by 820-446C (S/N A1461P-)
BLADE DISC 20RC X.256 ROLLABLE
820-444C
12.
Rev. 1
Replaced by 820-446C (S/N A1462P+)
BLADE DISC 20RC .256X1.78 HOLE
820-360C
12.
BLADE DISC 26RC X.256 ROLLABLE
820-467C
12.
7-Blade Gang 7 1/2", 6-Blade Gang 9"
GANG BOLT 50 3/4"
556-125D
13.
7-Blade Gang 9"
GANG BOLT 59 3/4"
556-126D
13.
8-Blade Gang 9"
GANG BOLT 68 3/4"
556-127D
13.
9-Blade Gang 9"
GANG BOLT 77 3/4"
556-128D
13.
10-Blade Gang 9"
GANG BOLT 86 3/4"
556-129D
13.
11-Blade Gang 9"
GANG BOLT 95 3/4"
556-130D
13.
12-Blade Gang 9"
GANG BOLT 104 3/4"
556-131D
13.
8-Blade Gang, 7 1/2"
GANG BOLT 58 1/4"
556-100D
13.
9-Blade Gang, 7 1/2"
GANG BOLT 65 3/4"
556-101D
13.
10-Blade Gang, 7 1/2"
GANG BOLT 73 1/4"
556-102D
13.
11-Blade Gang, 7 1/2"
GANG BOLT 80 3/4"
556-103D
13.
12-Blade Gang, 7 1/2"
GANG BOLT 88 1/4"
556-104D
13.
13-Blade Gang, 7 1/2"
GANG BOLT 95 3/4"
556-130D
13.
14-Blade Gang, 7 1/2"
GANG BOLT 103 1/4"
556-105D
13.
15-Blade Gang, 7 1/2"
GANG BOLT 110 3/4"
556-106D
13.
16-Blade Gang, 7 1/2"
GANG BOLT 118 1/4"
556-107D
13.
WASHER DURA-TIGHT 1.81ID X 7.0
804-200C
14.
Rev. 2
WASHER 2 3/4 X 1 3/4 X 1/4 PLT
804-229C
15.
Rev. 1
Changed to 804-229C
WASHER MACH 2 1/2X1 3/4X10GA
804-205C
15.
NUT HEX SLOTTED 1 3/4-5 REGULR
803-339C
16.
Rev. 2
CASTING THREAD PROTECTOR
812-365C
17.
Rev. 1
Replaced by 556-365C
THREAD PROTECTOR
556-067H
17.
Rev. 1
Was 6" Long
U-BOLT 3/4-10 X 5 1/32 X 6 1/2
806-120C
18.
WASHER LOCK SPRING 3/4 PLT
804-023C
19.
NUT HEX 3/4-10 PLT
803-027C
20.
05/21/12
- 79 -
556-100P
Section 5: Gangs
Disk Gang Assembly, 7 1/2" & 9" Spacing
(Applies to 3323DH, 3326DH, 3329DH, 4330DH, 4333DH, 4336DH only)