Great Plains 2000 Parts Manual - Manual (Page 105)

Revision Comments Part Description Part No. Ref.
Image No. dwg12692
SPKT 40B14 X 3/4 HEX BORE 808-167C 1.
PIN ROLL 3/16X1 1/4 PLT 805-023C 2.
Option 00 Opener. CHAIN RL #40 X 132 PITCHES 809-112C 3.
2nd rev. Option 10 & 20 Openers. CHAIN RL #40 142 PITCHES 136-115D 3.
Use existing stock; 1st rev. Option 10 & 20 Openers. RPBY 136-115D 809-147C 3.
NUT NYLOCK JAM NUT 1/2-13 803-178C 4.
NUT HEX JAM 1/2-13 PLT 803-036C 5.
NO. 40 12T IDLER SPKT. 817-025C 6.
HHCS 1/2-13X3 GR5 802-039C 7.
NUT HEX JAM 5/8-11 PLT 803-023C 8.
WASHER LOCK SPRING 5/8 PLT 804-022C 9.
WASHER FLAT 5/8 USS PLT 804-019C 10.
SPROCKET 40A17 IDLER 808-046C 11.
HHCS 5/8-11X3 1/2 FTHD 802-436C 12.
NUT HEX 3/8-16 PLT 803-014C 13.
WASHER LOCK SPRING 3/8 PLT 804-013C 14.
WASHER FLAT 3/8 USS PLT 804-011C 15.
HHCS 3/8-16X1 1/2 GR5 802-022C 16.
NUT HEX 5/16-18 PLT 803-008C 17.
WASHER LOCK SPRING 5/16 PLT 804-009C 18.
FLANGETTE 52 MST 822-032C 19.
BRG 7/8HEXX2.05OD SPH 822-119C 20.
SHAFT HEX 7/8 X 18 1/4 120-226D 21.
IDLER AND BRG MOUNT PLATE 123-515D 22.
IDLER AND BRG MNT PLT EXTENDED 123-531D 22.
RHSNB 5/16-18X1 GR5 802-282C 23.
SPKT 40B29 X 7/8 HEX BORE & SS 808-168C 24.
REAR DRIVE BRG MOUNT PLATE LH 123-517D 25.
SPKT 40B12 7/8 HEX BORE W/SS 808-143C 26.
2nd rev. CHAIN RL #40 61 PITCHES 136-060D 27.
Use existing stock; 1st rev. RPBY 136-060D 809-065C 27.
2nd rev. CHAIN RL #40 100 PITCHES 136-110D 28.
Use existing stock; 1st rev. RPBY 136-110D 809-142C 28.
HHCS 1/2-13X1 1/2 GR5 802-091C 29.
WASHER LOCK SPRING 1/2 PLT 804-015C 30.
WASHER FLAT 1/2 SAE PLT 804-016C 31.
NUT HEX 1/2-13 PLT 803-020C 32.
AGITATOR IDLER BOLT 5/8-11 118-439H 33.
SPKT 40B17X3/4 HEXBR&LCK COLLR 118-592H 34.
SCREW SET 5/16-18 SKT KP X 3/8 801-035C 35.
HHCS 5/8-11X1 1/4 GR5 802-050C 36.
For 15' & 20' only GAUGE WHEEL MOUNT LH DRIVE 120-209H 37.
For 12' only GAUGE WHEEL MOUNT RH DRIVE 120-210H 37.
09/25/13 - 105 - 118-389P
Table of Contents Part Number Index
Drive
Agitator Drive
(Applies to 1200 (1994+), 1500 (1994+), 2000 (1994+) only)