Tundra E150 - Manual (Page 3)

TUNDRA INTERNATIONAL INC.
2041-A, Leonard-de Vinci, Sainte-Julie (Quebec) Canada J3E 1Z2
Tel : 450.649.2470 / 1.877.964.2582 Fax : 1.888.855.9834
E-AUTO-GD-0512-EN
E 600
PROFESSIONAL SERIES
Thank you for the purchase of a
Tundra International product!
In order to get the most out of your
inverter, it must be installed and used
properly. Please thoroughly read this
manual before installing and using your
new inverter.
It is important to pay special attention
to the “WARNING” statements in this
manual as well as on the inverter.
How to use your new inverter
If you want to plug your inverter directly
on the car’s battery, use the cables
included with the inverter and fix each
end solidly on the inverter and the
battery. Without tightening them too
much, the terminals must not be able to
move around. The cables must go from
the positive terminal of the inverter to
the positive terminal of the battery, and
from the negative terminal of the inverter
to the negative terminal of the battery.
It is also possible to install the inverter
permanently into your vehicle by using
AWG #6 cables (3 meters max.) and a
60A fuse mounted as close as possible to
the battery. Only a qualified technician
must perform this procedure.
Before using the inverter, make sure that
the total amount of current asked will not
exceed the capacity of the inverter (600
watts).
WARNING! Reversing the
polarity when connecting the
DC cables will permanently
damage your inverter. THIS IS
NOT COVERED BY THE
WARRANTY.
Specifications
DC Input voltage 12 volts
AC Output voltage 120 volts
Output sine wave Modified
Frequency 60 Hz
Output power 600 watts
Low voltage alarm 10.5 volts
Low voltage shut down 10 volts
High temp. shut down 55oC ±5%
Maintenance
Be sure to disconnect the inverter from
the battery or the lighter plug before
cleaning, and use only a dry cloth to do
so.
WARNING! The inverter must
never be exposed to water or
humidity.
Placement and storage
Place the inverter in a dry and cool
environment and avoid putting it under
the sunshine or near a heat source. Do
not place it near any flammable or easy
melting materials.
WARNING!

Do not use if the power source is not
12 volts.

When you stop using the inverter, be
sure to pull out the plug.

Because the temperature of the metal
pieces of the inverter might be high,
do not place it near any flammable or
easy melting materials.

The voltage protection system will
automatically shut off the inverter if
the input voltage is too low. Start
your car engine to charge the battery,
or stop using the inverter.

Be sure your inverter is OFF when
starting the vehicle engine.

If the consumption power is over the
inverter capacity, the over load
protection system will automatically
shut off the inverter. If the inverter
doesn’t come ON again by himself,
to turn it on again, decrease the
consumption and turn the switch to
OFF position and then to ON.

The modified sine wave produced by
the inverter may cause some buzzing
and lines on audio and video
equipment.

We strongly recommend using a Pure
Sine Wave inverter for all of your
electronic sensitive equipments.

Stop using the inverter if the power
cord/plug has been damaged or
loosen. Have it repaired before using
it again.

Do not insert any object in the
inverter; it may cause fire, electric
shock or short circuit.

If there is any abnormal noise, smell
or smoke, turn off immediately the
inverter and contact your retailer.

Do not place any heavy object on the
inverter or the power cord.

Do not allow water drip or splash on
the inverter. Do not touch the case or
the power cord with wet hands.

Do not attempt any reparation or
modification; it may cause electric
shock or fire. When needed, contact
your retailer.
If the inverter has been exposed to rain,
moisture, or strong impact, have it
inspected by a qualified technician
before use.