beautypg.com

SONIQ AWM3001 User Manual

Assembly instructions, For adjustable flat panel wall mount, Supplied parts

background image

ASSEMBLY INSTRUCTIONS

FOR ADJUSTABLE FLAT PANEL WALL MOUNT

This product is designed to mount flat panel televisions weighing up to 132lbs/60kgs to a vertical wall with
maximum flat panel wall mount installing hole dimensions 75.5cm (width) x 48cm (height). It allows you to
effortlessly tilt your new television up or down without using tools.

Before installing our wall mount product,

please make sure your unit installing hole

dimensions is covered in product maximum

supported range.

Be careful to make sure there are no missing or defective parts.

Never use defective parts.

Improper installation may cause damage or serious injury.

Note The included hardware is for mounting on walls with wood stud construction.

If you are uncertain about the nature of your wall, consult an expert.

Please consult your hardware or installation professional for proper mounting to other types or walls.

The supplied hardware is not for steel.

Safety Warning:

SUPPLIED PARTS:

g: Plastic Cover x4

d: 1”Diameter Tube x2

r: Vise Assembly (small) x4

b: Arm Assembly x1

c: Monitor Brackets x2

a: Wall Plate x1

e: 1/4x2.5" Lag Bolt x6

Screw

Manihce

8

M

:

h

f: Concrete Anchor x6

M8x25x4 and M8x40x4

: M6x30 Machine Screw x4

i

m: M4/M5 Washer x12

p: Axle Pin & Safety Bolt x4

n: Plastic Spacer x4

l: Lag Bolt Washer x10

j: M5x30 Machine Screw x4

k: M4x30 Machine Screw x4

q: Axle Pin &Safety Bolt x2

s: Vise Assembly (big) x2

t: AllenKey (x2)

1a.BRICK,SOLID CONCRETE AND CONCRETE BLOCK MOUNTING:

.

s

d

u

t

s

d

o

o

w

o

w

t

o

t

d

e

t

n

u

o

m

e

b

:

E

T

A

L

P

L

L

A

W

E

H

T

G

N

I

T

N

U

O

M

.

b

1

Use the

(a) as a template to mark 6 hole locations on the

wall. Three in the top row of slots and three more in the bottom row. Make sure these holes are level and there is at least 150mm between any
two holes. Pre-Drill these holes with a 10mm masonry bit to at least 60mm in depth. Insert a Concrete Anchor (f) into each of these holes, Pre-
Drill these holes with a 5mm flush with the concrete surface even if there is a layer of drywall or other material in front. Attach the

to

the wall using 6 Lag bolts (e) and 6 M4 / M5 Washer (m).

o

w

t

e

t

a

c

o

l

o

t

r

o

s

n

e

s

d

u

t

s

y

ti

l

a

u

q

h

g

i

h

a

e

s

U

)

a

(

e

h

T

adjacent studs. It is a good idea to verify where the studs are located with an awl or thin nail shown in diagram 1-A. Pre-drill a 3mm deep hole
at the desired height in each stud using a 4mm drill bit. Make sure these holes are in the center area of the studs and level with each other.
Use the

as a template to mark the location of the second hole in each stud. Pre-drill these two holes using the 4 drill bit as well.

Attach the

to the wall using for the four Lag Bolts (e). Make sure the

is oriented so the flat surface in the center of the

plate in against the wall shown in diagram 1-B.

Wall Plate

Wall Plate

wall plate

Wall plate

e

t

a

l

P

ll

a

W

e

t

a

l

P

ll

a

W

WARNING :Tighten Lag Bolts (e) only until Lag Bolt Washer (l) is pulled firmly against the Wall Plate (a).DO NOT OVERTIGHTEN THE

BOLTS!

MUST

o: Plastic Spacer x4

75.5cm

48cm

Maximum support width

wall mount installing hole

Maximumsupport

highwallmount

installinghole