Blizzard Lighting ToughPAR (Rev A) - Manual (Page 9)

Page 12
ToughPAR 1 Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
DMX Mode
Allows the unit to be controlled by any universal DMX controller.
1.) The default mode for the fi xture is DMX, which appears as
d001
on the LED
Readout. To select a different DMX address, using the
Addr
,then hit . Use the buttons to select the correct
address, then hit to confi rm.
Stand-Alone, Master/Slave, Sound Active Modes:
Allows a single or Master/Slaved units to run factory installed programs at user selectable
speeds.
1.) To set the fi xture in Flash/Fade mode, select
FLAS or FAdE
To confi rm, press the button.
2.) Now, select the fl ash or fade speed using
SP--
,
then hit .
The display reads
SP15
(slowest) to
SP00
(fastest), then press the
TER> button to confi rm.
3.) To use the fi xture in automatic mode, select
ASC-
, then press the
TER> button to confi rm.
4.) Adjust the speed of the chase as above using
SP15
(slowest) to
SP00
(fastest) then press the button to confi rm.
5.) To set the fi xture as a slave unit, select
SLAV
, and hit . The unit
will display a fl ashing
SL-U
to indicate it is in slave mode.
Sound Acitve Mode:
1.) To use sound active mode, select
SouA
, then press the button
to confi rm.
Standalone (Program) Mode:
Allows a single unit to display a variety of colors and programs without a DMX controller.
1.) To set the fi xture in manual mode, select
Pr--
.
To confi rm, press the button.
2.) Now, select the program by using the and buttons to select
Pr00-Pr15
. To confi rm, press the button.
Manual Color Adjustment:
Allows the user to adjust the color balance of the fi xture. These settings are global, they
will effect all modes.
1.) Use the
rL--
(Red Level),
GL--
(Green Level),
bL--
(Blue Level) or
UL--
(White Level), then hit
.
2.) Using the buttons, select the maximum level for each color
between
x000-x255
(000=off), then hit to confi rm.
Page 9
ToughPAR 1 Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3 pin connector side of the
DMX cable to the output (female) 3 pin connector of
the fi rst fi xture.
2. Connect the end of the cable coming from the
fi rst fi xture which will have a (female) 3 pin connec-
tor to the input connector of the next fi xture con-
sisting of a (male) 3 pin connector. Then, proceed
to connect from the output as stated above to the
input of the following fi xture and so on.
A quick note: Often,
the setup for Master-
Slave and Standalone
operation requires that
the fi rst fi xture in the
chain be initialized for
this purpose via either
settings in the control
panel or DIP-switches.
Secondarily, the fi xtures
that follow may also re-
quire a slave setting.
Check the “Operating Adjustments” section in this manual for com-
plete instructions for this type of setup and confi guration.
Mounting & Rigging
This fi xture may be mounted in any SAFE position provided there is
enough room for ventilation.
It is important never to obstruct the fan or vents pathway. Mount the
fi xture using a suitable “C” or “O” type clamp. The clamp should be
rated to hold at least 10x the fi xture’s weight to ensure structural sta-
bility. Do not mount to surfaces with unknown strength, and ensure
properly “rated” rigging is used when mounting fi xutres overhead.
Adjust the angle of the fi xture by loosening both knobs and tilting the
fi xture. After fi nding the desired position, retighten both knobs.
• When selecting installation location, take into consideration lamp
replacement access (if applicable) and routine maintenance.
• Safety cables MUST ALWAYS be used.
• Never mount in places where the fi xture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.