Appendix, Page 13, A quick lesson on dmx – Blizzard Lighting The Puck 3NX (Rev A) User Manual

Page 13

Page 13

The Puck 3NX Manual Rev. B

5. APPENDIX

A Quick Lesson On DMX

DMX (aka DMX-512) was created in 1986 by the United States Institute for Theatre

Technology (USITT) as a standardized method for connecting lighting consoles to lighting

dimmer modules. It was revised in 1990 and again in 2000 to allow more fl exibility. The

Entertainment Services and Technology Association (ESTA) has since assumed control over

the DMX512 standard. It has also been approved and recognized for ANSI standard clas-

sifi cation.

DMX covers (and is an abbreviation for) Digital MultipleXed signals. It is the most common

communications standard used by lighting and related stage equipment.

DMX provides up to 512 control “channels” per data link. Each of these channels was origi-

nally intended to control lamp dimmer levels. You can think of it as 512 faders on a lighting

console, connected to 512 light bulbs. Each slider’s position is sent over the data link as an

8-bit number having a value between 0 and 255. The value 0 corresponds to the light bulb

being completely off while 255 corresponds to the light bulb being fully on.

DMX data is transmitted at 250,000 bits per second using the RS-485 transmission stan-

dard over two wires. As with microphone cables, a grounded cable shield is used to prevent

interference with other signals.

There are fi ve pins on a DMX connector: a wire for ground (cable shield), two wires for

“Primary” communication which goes from a DMX source to a DMX receiver, and two wires

for a “Secondary” communication which goes from a DMX receiver back to a DMX source.

Generally, the “Secondary” channel is not used so data fl ows only from sources to receiv-

ers. Hence, most of us are most familiar with DMX-512 as being employer over typical

3-pin “mic cables,” although this does not conform to the defi ned standard.

DMX is connected using a daisy-chain confi guration where the source connects to the input

of the fi rst device, the output of the fi rst device connects to the input of the next device,

and so on. The standard allows for up to 32 devices on a single DMX link.

Each receiving device typically has a means for setting the “starting channel number” that

it will respond to. For example, if two 6-channel fi xtures are used, the fi rst fi xture might

be set to start at channel 1 so it would respond to DMX channels 1 through 6, and the next

fi xture would be set to start at channel 7 so it would respond to channels 7 through 12.

The greatest strength of the DMX communications protocol is that it is very simple and

robust. It involves transmitting a reset condition (indicating the start of a new “packet”),

a start code, and up to 512 bytes of data. Data packets are transmitted continuously. As

soon as one packet is fi nished, another can begin with no delay if desired (usually another

follows within 1 ms). If nothing is changing (i.e. no lamp levels change) the same data will

be sent out over and over again. This is a great feature of DMX -- if for some reason the

data is not interpreted the fi rst time around, it will be re-sent shortly.

Not all 512 channels need to be output per packet, and in fact, it is very uncommon to fi nd

all 512 used. The fewer channels are used, the higher the “refresh” rate. It is possible to

get DMX refreshes at around 1000 times per second if only 24 channels are being trans-

mitted. If all 512 channels are being transmitted, the refresh rate is around 44 times per

second.

In summary, since its design and evolution in the 1980’s DMX has become the standard

for lighting control. It is fl exible, robust, and scalable, and its ability to control everything

from dimmer packs to moving lights to foggers to lasers makes it an indispensible tool for

any lighting designer or lighting performer.