Blizzard Lighting COLORStorm PAR LED Wash - Manual (Page 2)

Page 3
COLORStorm™ PAR Manual Rev. A Copyright (c) 2010 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
• 1 x COLORStorm™ PAR LED Wash
• An Ever-So-Handy Power Cord
• This Lovely User Manual
Getting It Out Of The Box
Congratulations on purchasing a fantastic, versitle LED wash light!
Now that you’ve got your COLORStorm (or hopefully, COLORStorms),
you should carefully unpack the box and check the contents to ensure
that all parts are present and in good condition. If anything looks as
if it has been damaged in transit, notify the shipper immediately and
keep the packing material for inspection. Again, please save the car-
ton and all packing materials. If a fi xture must be returned to the fac-
tory, it is important that the fi xture be returned in the original factory
box and packing.
Powering Up!
All fi xtures must be powered directly off a switched circuit and cannot
be run off a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel is used solely for a 0% to
100% switch.
AC Voltage Switch - Not all fi xtures have a voltage select switch, so
please verify that the fi xture you receive is suitable for your local pow-
er supply. See the label on the fi xture or refer to the fi xture’s specifi -
cations chart for more information. A fi xture’s listed current rating is
its average current draw under normal conditions. Check the fi xture or
device carefully to make sure that if a voltage selection switch exists
that it is set to the correct line voltage you will use.
Warning!
Verify that the voltage select switch on
your unit matches the line voltage applied. Damage to
your fi xture may result if the line voltage applied does
not match the voltage indicated on the voltage selector
switch. All fi xtures must be connected to circuits with a
suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, just give us a call or send an email.
We’ll be happy to help, honest.
Blizzard Lighting
2705 Brookview Ct., Brookfi eld, WI 53005 USA
[email protected] -- 414.979.5781
www.blizzardlighting.com
Page 4
COLORStorm™ PAR Manual Rev. A Copyright (c) 2010 Blizzard Lighting, LLC
SAFETY INSTRUCTIONS
• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.
• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the de-
cal or rear panel of the fi xture.
• This product is intended for indoor use only.
• To prevent risk of fi re or shock, do not expose fi xture to rain or moisture.
• Make sure there are no fl ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.
• ALWAYS secure fi xture using a safety chain. NEVER carry the fi xture by its
head. Use its carrying handles.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized tech-
nical assistance center. Always use the same type spare parts.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please contact Blizzard Lighting at sup-
[email protected].