Bang & Olufsen BeoLab 5 - pin code correction - Manual (Page 3)

3
To change your PIN code
In order to change the PIN code, you must first key
in your previously chosen four-digit code, and then
key in a new code. However, you can only do so
five times within a three-hour time period!
While BeoLab 5 is in standby...
> Press , , and STOP in quick succession on the
Beo4 remote control.
The indicator light shines intermittently red
(1 sec.) and green (0.5 sec.).
> Within 10 seconds, press the touch field on top
of the loudspeaker you wish to change the PIN
code for.
The loudspeaker confirms your selection with a
sound signal.
> Key in your previously chosen four-digit PIN code*.
The loudspeaker confirms each digit with a
sound signal.
> Press the GO (PLAY) button to be able to enter
your new four-digit code.
The loudspeaker confirms this with a sound
signal.
> Key in a new four-digit code of your own choice*.
The loudspeaker confirms each digit with a sound
signal.
> Press the GO (PLAY) button to accept your code.
The loudspeaker confirms this with a sound
signal.
> To confirm your new code, key in the new four-
digit code again*.
The loudspeaker confirms each digit with a
sound signal.
> Press the GO (PLAY) button to store your code.
The loudspeaker confirms this with a sound signal.
If the PIN code is accepted, the indicator light
shines red for a while and then switches off.
If it is not accepted the loudspeaker emits a sound
signal, and you will have to start over again with
the four-digit code.
If you have forgotten your PIN code
You will need a five-digit master code in order to
unlock the loudspeaker. Please contact your
Bang & Olufsen retailer to get a master code from
Bang & Olufsen.
When unlocked via a master code the PIN code
system is deactivated!
While BeoLab 5 is in standby...
> Press and hold on the Beo4 remote control for
three seconds to enable master code input.
The indicator light shines intermittently red
(1 sec.) and green (0.5 sec.).
> Within 10 seconds, press the touch field on top
of the loudspeaker you wish to activate.
The loudspeaker confirms your selection with a
sound signal.
> Key in the five-digit master code you received
from Bang & Olufsen*.
The loudspeaker confirms each digit with a
sound signal.
> Press the GO (PLAY) button to store the five-
digit master code.
The loudspeaker confirms this with a sound signal.
If the master code is accepted, the indicator light
shines red for a while and then switches off.
If it is not accepted the loudspeaker emits a sound
signal, and you will have to start over again with
the five-digit master code.
To deactivate the PIN code system
In order to deactivate the PIN code system you must
first key in your previously chosen four-digit code,
and then key in the ‘0000-code’, which disables the
function.
While BeoLab 5 is in standby...
> Press , , and STOP in quick succession on the
Beo4 remote control.
The indicator light shines intermittently red
(1 sec.) and green (0.5 sec.).
> Within 10 seconds, press the touch field on top
of the loudspeaker you wish to deactivate.
The loudspeaker confirms your selection with a
sound signal.
> Key in a your previously chosen four-digit PIN
code*.
The loudspeaker confirms each digit with a
sound signal.
> Press the GO (PLAY) button to enter your code.
The loudspeaker confirms this with a sound
signal.
> Key in the digits 0 0 0 0 on the Beo4 remote
control*.
> Press the GO (PLAY) button to deactivate the
PIN code system.
The indicator light shines red for a while and then
switches off.
If it is not accepted the loudspeaker emits a sound
signal, and you will have to start over again with
the ‘0000 code.