Therma-Tru Door System Specifications User Manual
Product manual, Spec, Classic-craft door system specifications

SPEC
Door System
Specifications
Product Manual
1
SPEC
Door System
Specifications
DOOR PANELS
GASKETING,
WEATHERSTRIPPING
HINGES, STRIKES,
MULTI-POINT
LOCKING SYSTEM
FRAMES
SILL, SWING-IN, SWING
OUT, SIDELITE OPTIONS
TRANSOM OPTIONS
OPTIONAL
DECORATIVE PANELS
Product Manual
Jacketed thermoset open-cell foam, press-fit in kerfs at jamb stops in frames. Extruded
thermoplastic elastomer, finned and chambered design, press-fit into bottom kerf of
doors. Corner pads at bottom margin corners from jacketed thermoset open-cell foam.
Milled from 5/4 kiln-dried pine, profiled with 1/2-inch stop, standard depth 4-9/16
inches. Other frame depths available to match wall constructions. Exterior casing
brickmould in WM180 pattern available. Optional frames in exterior grade red oak with
matching brickmould. Optional rot resistant jambs.
Wide range of sill options: fixed threshold, adjustable threshold, and public access
available in bronze, mill, satin nickel and brass finishes.
Double-door models: double door available with both leaves active and locking astragal
available.
Sidelite options:
flush-glazed or lite insert models, with embossed panel & glass
moldings, in 10 inch, 12-inch and 14-inch widths. Sidelite systems available with
mullions separating doors from sidelites, and continuous sills and frame head, or as
separately framed and cased units joined together.
Transom frames, either rectangular, elliptical or half round, match door frames and have
matching exterior brickmould. Transom frames in primed pine or clear northern red oak
to match door frame option. Low-E or etched insulated glass. Options for leaded
decorative glass panel in air space between tempered glass panes with brass, brushed
nickel or black nickel caming finishes.
OPTIONAL
FACTORY-GLAZED
GLASS OR GLASS
INSERTS
Classic-Craft Door System Specifications
Faces:
3/32-inch minimum thickness, proprietary fiberglass reinforced thermoset
composite, textured to duplicate hand-crafted hardwood master or smooth surface,
stainable and paintable. Door edges: machinable kiln-dried hardwood, flush and
square with door faces, lock edge reinforced with full-length integrated 3-1/2-inch wide
engineered lumber core. Door bottom edge: moisture- and decay-resistant composite.
Core:
foamed-in-place polyurethane, density 1.9 pcf minimum.
Except where
certification does not permit, standard factory sizes may be edge trimmed or end
trimmed in shop or field to suit replacement door size requirements.
Factory-glazed: perimeter moldings flush with skin and made as integral part of skin.
Glass: minimum 1/8-inch tempered, two panes with sealed airspace between, air-space
typically 1/2-inch. Options for leaded decorative glass panel in airspace between
tempered glass panes with brass, brushed nickel or black nickel caming finishes.
Etched glass options. Optional removable wood grilles. Optional permanent external
lite dividers
Inserts (lites): perimeter frames in raised-molding patterns, composite frame moldings
wood grained or matte black aluminum, with molding patterns complementing raised
panel moldings, stainable or paintable, screw-fastened to doors, screw holes concealed
with grained plugs in matching material. Glass: minimum 1/8-inch tempered, two
panes with sealed airspace between, airspace typically 3/4-inch. Options for leaded
decorative glass panel or wrought iron grille in air space between tempered glass panes
with brass, brushed nickel or black nickel caming finishes.
Wrought iron grille
available in matte black only. Etched glass options. Optional removable wood grilles.
Molded from proprietary fiberglass-reinforced thermoset composite, wood grained to
match door faces, stainable or paintable, fastened with very high bond tape.
Steel,
with variety of finishes. Screws plated and finished to match
hardware.
hinge size 4 x 4 x .098 inches. Strikes are proprietary adjustable
type, permitting in-out adjustment of door in frame, up to 3/16 inch.
ball-bearing design,
a
Standard
Multi-point locking
system is available in manual shootbolt or tongue versions.