Kuryakyn 4232 UNIVERSAL HELMET LOCK - Manual

CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products sold
hereunder, shall be free of defects in materials and
workmanship for a period of one (1) year from the
date of purchase by the consumer excepting the fol-
lowing provisions:
• Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt showing
the date the customer purchased the product(s).
• The product must be properly installed,
maintained and operated under normal conditions.
• Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated products.
• Küryakyn shall not be liable for any consequential
and incidental damages, including labor and
paint, resulting from failure of a Küryakyn product,
failure to deliver, delay in delivery, delivery in noncon-
forming condition, or for any breech of contract or
duty between Küryakyn and a customer.
• Küryakyn products are often intended for use
in specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
• Küryakyn electrical products are warranted for one
(1) year from the date of purchase by the consumer.
Components of Küryakyn products containing L.E.D.s
will be warranted for defects in materials and
workmanship for 3 years from the date of purchase.
• Küryakyn makes no warranty of any kind in regard
to other manufacturer’s products distributed by
Küryakyn. Küryakyn will pass on all warranties made
by the manufacturer and where possible, will expedite
the claim on behalf of the customer,
but ultimately, responsibility for disposition of the
warranty claim lies with the manufacturer.
ABOUT OUR CATALOG
You’ll find all our innovations for H-D, GL and
Metric Cruisers in our annual catalogs. Order online
today–select the ”CATALOGS” icon. Each Küryakyn®
product comes with a Proof-of-Purchase good for a
complimentary catalog. Details in packaging.
Be sure to ask your local dealer about other
Küryakyn products, the motorcycle parts and ac-
cessories designed for riders by riders.
©2005 Küryakyn USA ® All Rights reserved.
I N S TA L L AT I O N
Parts Included
1 Universal Helmet Lock assembly
2 Keys on ring
2 Tamper-proof screws
1 Installation Instructions
Please read and understand entire instructions before starting installation.
thank you for choosIng küryakyn!
Please note
It is the installers’ responsibility to make sure all fasteners (including pre-assembled) are
tightened before operation of motorcycle. Küryakyn will not warranty components that are
lost due to improper installation. Periodic maintenance may be required.
ATTEnTIOn! Test fit the helmet lock location before fully tightening the tamper-proof
screws. It is extremely difficult to remove the screws.
WARnInG! AvOID LOSS Of COnTROL, DAMAGE AnD SERIOUS InjURY OR DEATH. DO
nOT OPERATE THE MOTORCYCLE WITH THE HELMET LOCKED InTO THE UnIvERSAL
HELMET LOCK.
tools suggested
flat blade screwdriver.
Procedure
steP 1 Park the motorcycle on a hard, level surface; turn off the ignition and allow the
engine to cool.
steP 2 Test fit the helmet lock on the motorcycle to ensure that the helmet will not
damage or interfere with any other components on your motorcycle. Do not install the
tamper-proof screws at this time.
note It is very important to perform the “test-fit” due to the extreme difficulty in
removing the tamper-proof screws after they are tightened.
ATTEnTIOn! Ensure clearance of painted surfaces
that could be damaged by a helmet or hot
surfaces that could cause damage to your helmet.
steP 3 Insert the tamper-proof screws through
the front side of the helmet lock as shown in PIC.1.
steP 4 Tighten screws evenly and ensure that
the helmet lock is properly clamped onto the tube.
-cont.-
fIts: any 1-1/4” to 1-1/2” round tube
4232-11HD-0107
u n I v e r s a l h e l m e t l o c k 4 2 3 2
PIc.1
be PosItIve of the
locatIon before
tIghtenIng tamPer-
Proof screws.