Kuryakyn 7686 CLUTCH ARM COVER - Manual

INSTALLATION
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
● The product must be properly installed,
maintained and operated under
normal conditions.
● Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
● Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
● Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
● Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
● Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with
your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.
PARTS INCLUDED
1 Clutch Actuating Arm Cover
1 Hardware Kit Containing:
1 M4 X .7 X 10mm Button Socket Cap Screw
1 Retaining Plate
1 Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING K ϋ RYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDING
THE USE AND CARE OF THIS PRODUCT.
WARNING! THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING
THE CONTENTS DESCRIBED HEREIN CAN RESULT IN
POTENTIAL DEATH OR SERIOUS INJURY.
ATTENTION!
This indication alerts you to the fact that ignoring the contents
described herein may negatively affect product performance and
functionality.
TOOLS SUGGESTED
Set of Hex Wrenches
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN
ORDER TO USE THE PRODUCT PROPERLY AND AVOID
POTENTIALLY DANGEROUS ACCIDENTS.
STEP 1 Read and understand all steps in the instructions
before starting the installation. Park the motorcycle
on a hard, level surface and turn off the ignition. Let
cool.
WARNING! YOU WILL BE WORKING AROUND THE
ENGINE AND EXHAUST SYSTEM DURING
INSTALLATION. ENSURE THAT THE
ENGINE AND EXHAUST SYSTEM HAVE
FULLYCOOLED TO PREVENT INJURY.
STEP 2
Loosely install the supplied Button Socket Cap Screw
into the post in the Cover. Place the Clutch Arm Cover
over the clutch arm. The post inside the Cover will
locate in the notch on the clutch arm. PIC 1
STEP 3 Slide the Retaining Plate under the Clutch Arm Cover
(there is a notch in the Retaining Plate that will fit
around the Button Cap Screw). Holding the retaining
plate in place, tighten the Button Cap Screw securely.
PIC 2
ATTENTION!
It is the installer’s responsibility to ensure that
all of the fasteners (including pre-assembled)
are tightened before operation of the
motorcycle. Küryakyn will not issue a warranty
on components lost due to improper installation.
Periodic maintenance may be required.
CLUTCH ARM COVER 7686
7686-21MC-1211
PIC 1
POST IN COVER
FITS IN THIS
NOTCH
BUTTON CAP
SCREW
RETAINING PLATE
PIC 2
Ride On!
PIC 3