Kuryakyn 5640 OIL COOLER COVER for INDIAN - Manual

THANK YOU FOR CHOOSING K ϋ RYAKYN!
PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND PROPERTY DAM-
AGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAU-
TIONS, AND NOTICES REGARDING THE INSTALLATION, USE, AND CARE OF THIS
PRODUCT.
MAKE SURE THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:
1 Oil Cooler Cover Assembly
1 Installation instructions
TOOLS SUGGESTED:
1/4” combination wrench and warm soapy water and a clean rag
STEP 1 Read and understand all steps in the instructions before starting the installation.
Park the motorcycle on a hard, level surface and turn off the ignition. Allow the en-
gine and exhaust system to cool.
STEP 2 Use warm soapy water and a clean rag to remove all grease, oil, bugs, dirt and other
debris from the installation area.
STEP 3 Snug the four screws so that the sliding tabs stay
in place in the open position. The larger metal tab
is on the top.
STEP 4 Position the Cover over the oil cooler; maneuver
the Cover in top side first.
STEP 5 Refer to PIC 1. Apply slight inward pressure on
the Cover, slide the tabs to the closed position
and tighten the screws.
INSTALLATION
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
● The product must be properly installed,
maintained and operated under
normal conditions.
● Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
● Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
● Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
● Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
● Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with your
address to: Küryakyn
454 County Road V V
Somerset, WI 54025-9031
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights
reserved.
OIL COOLER COVER for INDIAN
5640-21MC-0514
THIS INDICATION ALERTS YOU TO THE FACT THAT
IGNORING THE CONTENTS DESCRIBED HEREIN CAN
RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indication alerts you to the fact that ignoring the
contents described herein may negatively affect product
performance and functionality or damage the product itself
or the product to which it is being attached.
5640
These installation instructions contain important information.
Ensure that the end user receives this copy and is aware of its
importance for future reference.
Avoid damage to the motorcycle. Protect painted surfaces
with a soft cloth or blanket.
Ride On!
YOU WILL BE WORKING AROUND THE ENGINE AND
EXHAUST SYSTEM DURING INSTALLATION. ENSURE
THAT THE ENGINE AND EXHAUST SYSTEM HAVE FULLY
COOLED TO PREVENT INJURY.
PIC 1
PUSH TOP TAB DOWN
PUSH BOTTOM TAB UP