Intelix DIGI-HD-1X4 - Manual (Page 2)

8001 Terrace Ave
Suite #201
Middleton, WI 53562 Phone: 608-831-0880
Toll-Free: 866-4-MATMIX
Fax: 608-831-1833
DIP Switch Settings
DIGI-HD-1X4 DIP Switch Positions
SW 1 SW 2 SW 3 Mode
off off off Dual Twisted Pair Mode – 1080p –
stereo audio
The distribution amplifier is preset with
EDID for 1080p video and PCM stereo
audio.
off on off Dual Twisted Pair Mode – 1080p – 5.1
audio
The distribution amplifier is preset with
EDID for 1080p video and Dolby Digital
5.1, DTS 5.1, and PCM stereo audio.
on off off Dual Twisted Pair Mode – EDID copy
The distribution amplifier uses custom
EDID copied from outputs.
on on off Dual Twisted Pair Mode – 1080i –
stereo audio
The distribution amplifier is preset with
EDID for 1080i video and PCM stereo
audio.
off off on Single Twisted Pair Mode – 1080p –
stereo audio
The distribution amplifier is preset with
EDID for 1080p video and PCM stereo
audio.
off on on Single Twisted Pair Mode – 1080p –
5.1 audio
The distribution amplifier is preset with
EDID for 1080p video and Dolby Digital
5.1, DTS 5.1, and PCM stereo audio
on off on Single Twisted Pair Mode – EDID copy
The distribution amplifier uses custom
EDID copied from outputs.
on on on Single Twisted Pair Mode – 1080i –
stereo audio
The distribution amplifier is preset with
EDID for 1080i video and PCM stereo
audio.
Troubleshooting
Symptom Possible Solutions
No signal
Status LED is off
Verify that both ends of the twisted pair
cables use 568B crimp pattern.
Verify HDMI cables and source and
destination HDMI ports are operational.
No signal Verify the power supplies are connected
to both the DA and receive baluns.
Verify the power LEDs on both the send
and receive units are brightly
illuminated.
Unusual colors in the video Power off the destination device and
power it back on to force renegotiation.
Unplug and re-plug the HDMI cable from
receive balun to force renegotiation.
No signal
Screen is completely snowy
Speckling in the video image
Occasional signal dropouts
Use shorter runs of twisted pair cabling.
Drop the HDMI signal to the next lower
resolution; i.e., decrease resolution from
1080p to 1080i, etc.
Replace the twisted pair cable with a
higher grade twisted pair cable; i.e.,
replace Cat 5e with Cat 6.
Speckling in the video image If the destination device is incapable of
displaying the video signal, alter the
source signal; i.e., decrease resolution
from 1080p to 1080i, etc.
Video without audio Change source device to output PCM
rather than Bitstream audio
Enable PCM down sampling if supported
by your source device
Copying Display EDID
1. Disconnect the DIGI-HD-1X4 from the source device and
extenders.
2. Disconnect the receiver from the destination device that
you desire to copy from.
3. Set transmitter DIP switches to EDID Copy mode (On,
Off, Off for Dual UTP extenders, or On, Off, On for Single
UTP Extenders)
4. Connect the DIGI-HD-1X4 Input to the destination device
input via an HDMI cable.
5. Connect the 5VDC power supply to the DIGI-HD-1X4 and
turn the device on with the power button.
6. Press the “EDID Copy” button on the DIGI-HD-1X4.
7. The Output LEDs will flash for 2-3 seconds then remain
solid. The EDID signals have been copied and stored.
8. Disconnect the DIGI-HD-1X4 from the destination.
9. Reconnect the DIGI-HD-1X4 and extenders following
normal installation procedures.