Black & Decker UCM200WG User Manual

Page 12

3. After brewing is complete, remove carafe from warming plate and serve.

Coffeemaker warming plate will cycle on and off to maintain proper coffee

temperature for one hour before it automatically shuts off and the Power Light

turns off.

4. Unplug and allow unit to cool for 10 minutes between cycles. Allow to cool

completely before attempting to clean.

Warning: Warming plate is hot! Do not touch bottom of carafe or warming plate

during or after brewing.
Note: After the unit is turned off or automatically shuts off after one hour, mill

coarseness setting will default to level 4 (medium grind). Coarseness setting will

also default to level 4 in the event of power interruption.
Note: The amount of coffee in the carafe may be slightly less than the amount of

water placed in the water reservoir, since some of the water is absorbed by the

coffee grounds.
BREWING COFFEE - PROGRAMMING DELAy TIMER
1. Follow steps 1 – 6 in BrEWINg COFFEE – IMMEDIATE STArT and 1-3 in

PrOgrAMMINg THE MILL.

2. Be sure clock is set to the current time (see SETTINg THE CLOCK instructions).
3. Press and hold the timer button

until the timer light appears and the

display reads 12:00. Use the Hour and minute buttons,

and

, to set the

desired programmed time. A small dot will appear in the upper left corner of

the display to signify A.M. No dot indicates P.M.

4. The timer display will flash 5 times then switch back to the current time of day.

Press and release the timer button

. The programmed time is now set and

the timer indicator light will turn on to indicate the timer has been reset.

Note: The programmable function must be reset after each programmed use.
SNEAK-A-CUP® INTERRUPT FEATURE
You can pour a cup of coffee while coffee is brewing without leaking from the

brew basket. When finished pouring coffee, place the carafe under brew basket.
The brewing process continues.
Important: To avoid possible overflow after removing the carafe, be sure to

replace the carafe under the brew basket within 20 seconds to prevent the basket

from overflowing.
KEEP WARM FUNCTION
The automatic keep warm function keeps coffee at the proper serving temperature

for up to 1 hour from brewing. To keep coffee hot, return the carafe to the

warming plate after serving.
To deactivate this function after brewing, simply press the power button

turn the unit OFF.
TO BREW A SECOND POT OF COFFEE
To brew a second pot of coffee, turn the coffeemaker OFF for 10 minutes and

allow it to cool. Empty used coffee grounds from the mill basket and repeat steps

for brewing.
Caution: Failure to allow appliance to cool completely may cause water to

overheat and spray hot steam. The hot steam can cause severe burns.

3. Lift up the reservoir cover and slowly pour water into the water reservoir. Place

empty carafe onto the warming plate.

4. Open the mill assembly lid and grasp mill basket tabs to remove the basket lid.

Using the scoop provided with your coffeemaker, measure the desired amount

of roasted whole bean coffee into the mill basket. We recommend using

1 scoop for every 2 cups of brewed coffee, which may be adjusted to suit your

individual tastes.

Note: 1 scoop = 1 tablespoon.
Warning: The Mill Basket maximum capacity is 8 scoops of whole bean coffee.

DO NOT EXCEED THE 8-SCOOP MAXIMUM.
Note: 8 scoops = 8 tablespoons maximum.
5. replace mill basket lid. Make sure that the basket is firmly seated in the

assembly, the lid on basket is secured, and that the mill assembly lid is closed

before attempting to operate unit.

Warning: The coffeemaker will not operate without the Lids being closed

properly.
Note: ground coffee may be substituted for whole bean coffee.
6. We recommend using 1/2 to 1 tablespoon of ground coffee beans for every

brewed cup of coffee, which may be adjusted to suit your individual tastes.

See PrOgrAMMINg THE MILL for complete procedure.

7. You are now ready to initiate the automatic mill and brew process. If you wish

to use the delay timer so you can program the coffeemaker to mill and brew

later, please read BrEWINg COFFEE - PrOgrAMMINg THE DELAY TIMEr.

PROGRAMMING THE MILL
Note: If you desire a medium grind, your machine is automatically preset to “4”

or a medium grind; refer to step 2 below. If you wish to program a finer or coarser

grind, start with step 1.
1. To set the mill to grind the beans to the desired level of coarseness, press

the

to select different coarseness levels. Seven levels of coarseness are

available. Coarseness is determined by the length of time milled - the longer

the time, the finer the grind the stronger the flavor. Setting 1 will mill the beans

for 15 seconds. Setting 7 will mill the beans for 40 seconds. If you do no select

a setting the unit will automatically default to setting 4. Make sure the mill light

is turned off.

Note: If you wish to use pre-ground coffee instead of whole coffee beans, press

the mill button

and make sure the mill indicator Light is on. If you are using

whole coffee beans, then the light should be off.
2. Press the power button

to initiate the mill and brew process; the power

light will turn on. Mill will start. After mill stops, unit will automatically switch

to brewing operation. To interrupt milling or brewing press the power button

and the power light will turn off.

Caution: Do not open lid until blades and unit operation has come to a

complete stop.