JLG T500J Parts Manual User Manual
Page 21
1-13
SECTION 1 FRAME
3311005
1
Locknut #10-24NC (With 2 inch Ball Only)
42
1
Lanyard Options (Not Used SN 0030002099 to
SN 0030002199):
42A
1060380
10in/25.4cm Length
42B
1060799
11-1/2in/29cm Length
43
3420592
1
Hairpin (Not Used SN 0030002099 to SN 0030002199)
44
3760170
1
Ring, Split (Prior to SN 0030002099 Only with Combination 2
inch Ball)
Ref
HYDRAULIC BRAKE AND AXLE INSTALLATION
0273608
Ref
T350 All Machines Except SNs 0030000121-0030000140,
0030000142,0030000143 & 0030000153
B
9984242
Ref
T350 SNs 0030000121-0030000140, 0030000142,0030000143 &
0030000153 Only
A
0273609
Ref
T500J
B
101
1
Axle Assembly with Hydraulic Brakes Options (See HYDRAULIC
BRAKE ASSEMBLY (ANSI & ANSI EXPORT SPEC MACHINES
for Breakdown):
0280154
T350 Except SNs 0030000121-0030000140, 0030000142,
0030000143 & 0030000153
Use 0280154
T350 SNs 0030000121-0030000140, 0030000142,
0030000143 & 0030000153 Only (was p/n 9984240)
0280155
T500J
102
0642012
4
Bolt 5/8in-11NC x 1-1/2in
103
3312005
4
Locknut 5/8in-11NC
104
4892000
8
Flatwasher 5/8in Hardened
105
9984241
8
Spacer (Not Shown) (T350 SNs 0030000121-0030000140,
0030000142,0030000143 & 0030000153 Only)
Ref
TIRE AND WHEEL INSTALLATION
Ref
T350
0273610
Ref
ANSI & ANSI Export Specs - Prior to SN 0030002529
B
0275210
Ref
ANSI & ANSI Export Specs - SN 0030002529 to Present
C
0275210
Ref
Australian Specs
C
Ref
T500J
0273611
Ref
ANSI & ANSI Export Specs - Prior to SN 0030002529
B
0275211
Ref
ANSI & ANSI Export Specs - SN 0030002529 to Present
B
0275211
Ref
Australian Specs
B
201
AR
Tire and Wheel Assembly
Use 1001109586
2
T350 (205-75-R14) (ANSI & ANSI Export Specs - Prior to
SN 0030002529) (Serviced as an Assembly Only) (was
p/n 4520323 & 4520613)
Use 1001109586
2
T350 (205-75-R14) (ANSI & ANSI Export Specs -
SN 0030002529 to SN 0030003105 & Australian Specs -
Prior to SN 0030003105) (Serviced as an Assembly Only)
(was p/n 4520613)
1001109586
2
T350 (215-75-R14) (ANSI & ANSI Export Specs -
SN 0030003105 to Present & Australian Specs -
SN 0030003105 to Present)
FIGURE 1-4. AXLE AND TONGUE INSTALLATION WITH HYDRAULIC BRAKES - WITH 2IN
BALL (ANSI, ANSI EXPORT & AUSTRALIAN SPEC MACHINES) (CONTINUED)
ITEM #
PART NUMBER
QTY.
DESCRIPTION
REV.