DiMarzio Ionizer 8 Neck - Manual (Page 2)

DiMarzio
®
4-Conductor
Pickup Instructions
For all DiMarzio pickups with side-by-side coils
Please Note -
If you have no previous experience with wiring or
feel uncertain how to proceed, we recommend having a professional
do the pickup installation.
General Instructions
If you have purchased our pickup to replace one that is currently in your
guitar, do the following:
•
Remove your old pickup carefully. Installing your new pickup will be
much easier if you unsolder your original pickup cleanly, rather than cut
its wire. Make a note of exactly where the old pickup was connected as,
in most cases, the new one will connect to the same place.
•
Use a soldering iron with a fine tip (25 to 45 watts) and thin rosin core
solder for all connections. If you intend to use a miniature switch with the
pickup, use a high quality switch and try to be as clean as possible with
the solder connections to avoid short circuits or damage to the switch.
•
To take full advantage of your new pickup, we strongly recommend
using DiMarzio parts and hardware. DiMarzio offers two push/pull
Potentiometers, the EP1200PP (250K) and the EP1201PP (500K). Both
of these controls are suitable for volume or tone, with double-pole,
double-throw miniature switches built in. The switches perform exactly
like separate miniature switches, and we recommend them in situations
where you do not want to drill extra holes in the face or pick guard of
your instrument.
IMPORTANT: although other brands of pickups may have the same
color wires as ours, the connections are not necessarily the same.
For our pickup to function properly, you must follow these
instructions.
Standard Humbucking Series Wiring
All DiMarzio 4-conductor pickups have red, black, green and white wires.
The standard wiring for most humbuckers is series humbucking. To do this,
solder the BLACK and WHITE wires together. Cover the solder connection
with tape so it does not touch any other part of the circuit. Solder the RED
wire to the hot connection in the guitar’s circuit. In most cases where you
are replacing a pickup, the RED wire will be soldered to the same place as
the hot, or center wire of the original pickup. The GREEN and BARE wire
are soldered to ground. Usually, this connection is made to the back of a
control. When connecting the BARE wire to ground, make sure it does not
come in contact with any other connections.
If you install a DiMarzio pickup in a two-pickup instrument and find the
pickups to be out of phase (weak and thin) when they are on together, you
must reverse the phase of one of the pickups. This applies to all DiMarzio
pickups with side-by-side coils or blades when installed in guitars with
single-coil pickups similar to Stratocasters. To reverse the phase of the
DiMarzio pickup, reverse the red and green wires. Solder the RED wire to
ground, and the GREEN wire to hot.
Standard Humbucking Parallel Wiring
There is a second way to wire a humbucking pickup, with the two coils in
parallel. The pickup will still cancel hum, but it will be slightly less powerful,
with more highs and an overall cleaner sound. To do this, solder the RED
and WHITE wires together. This will be the hot connection. Solder the
GREEN and BLACK wires together. This will be the ground connection.
The bare wire will also be grounded. If you need to wire the pickup for
reverse phase, the GREEN and BLACK connection will be hot and the
RED and WHITE connection will be ground. The bare wire will still be
grounded.
Dual Sound
This wiring will produce two sounds. One is with the pickup coils in series
for maximum power. The second sound is with the coils in parallel. Parallel
wiring is not the same as turning off one coil. Turning off a coil means the
pickup is no longer humbucking, and no longer cancels hum. Dual Sound
wiring cancels hum in both positions. A double-pole, double-throw (DPDT)
miniature switch (DiMarzio EP1106) or a push-pull pot (EP1200PP or
EP1201PP) is required for this option, and the wiring looks like this:
Be sure to make the jumper connection between poles 3 and 5 of the
switch. The wire labeled HOT OUTPUT should be connected to the same
place as your original pickup. The wire labeled TO GROUND is soldered to
ground.
To reverse the phase of the pickup, use pole 4 as the HOT OUTPUT and
connect pole 1 TO GROUND. The bare wire from the 4-conductor cable is
always soldered to ground.
Dual Sound with Single-Coil Switching
Following the same diagram above, you can use a three-position (on-on-on)
DPDT mini switch (DiMarzio EP1108.) The two outside positions will be
series and parallel; the center position will be single-coil.
Phase Switch
Phase switching can only function in an instrument with two or more
pickups. The effect will only occur when both pickups are on, and will be
most obvious when the pickups are at approximately the same volume.
Only one of the pickups should be wired to the phase switch, and it makes
no audible difference which pickup you choose. The switch should be
DPDT, the same type as for Dual Sound switching (DiMarzio EP1106) or
push-pull pot (EP1200PP or EP1201PP).
If you want to wire the pickup to both a Dual Sound switch and a phase
switch, first wire the pickup to the Dual Sound switch the same way as
shown in the Dual Sound instructions; then connect the Dual Sound switch
to the phase switch like this:
The wire labeled HOT OUTPUT is connected to the same spot as the
original pickup. The wire labeled TO GROUND is soldered to a ground
connection, such as the back of a control. The bare wire from the 4-
conductor cable should also be soldered to ground.
Single-Coil Switching (Coil Tapping, Coil Splitting)
Single-coil switching will produce a brighter, cleaner sound. With all side-by-
side humbuckers, the volume will be less than with standard humbucking
series wiring. With vertical humbuckers, such as the HS™, Area™ and
Virtual Vintage
® series, the volume will be slightly greater as long as the coil
closest to the strings (the one with red and black wires) remains on.
A switch is required for single-coil switching. It can be the same type of
DPDT as is used for Dual Sound or phase switch, or a simpler single-pole,
double-throw switch. The diagram shows the DPDT type.
The BARE wire is always soldered to ground. As only one side of the
DPDT mini-switch is used, you may choose to have two pickups go from
double- to single-coil on one switch, like this:
If you want to combine a phase switch with a single-coil switch, the diagram
is this:
An interesting feature of this arrangement is that the phase switch has two
functions. When two pickups are on together, it performs its normal task.
When the pickup shown above is on alone and the single-coil switch is on,
the position of the phase switch determines which of the two coils is turned
off, giving a subtle variation in tone. Phase switching should not be
combined with coil tapping on HS™, Area™ and Virtual Vintage
® models. In
one position, it will turn only the bottom coil on, producing almost no signal.
Treble Compensation
Many players notice a loss of high frequencies when the volume control is
turned down. To avoid this, install a 560pF capacitor alone or with a 300K
ohm resistor (270K or 330K will also work) in parallel across the two “hot”
legs of the volume control, as shown in the drawing. Try to solder these
components cleanly to the legs of the volume control, without breaking the
solder connections that are already present.
Component Values
500 Kohm is the most common resistance value most guitar companies and
players employ with humbuckers for both volume and tone controls. Using
250 Kohm controls will result in a little warmer sound and a slight drop in
power. DiMarzio also offers a 1 Megohm tone control (DiMarzio EP1202)
which slightly increases treble response and power. This control can be
combined with either 250 Kohm or 500 Kohm volume controls. We
recommend .022 µF for the capacitor on the tone control.
Additional Notes
Wiring diagrams and technical information may be found on our website:
www.dimarzio.com
All DiMarzio pickups have been potted in an exclusive wax formula to
eliminate squeal and subdue extraneous noise. For further noise reduction,
we recommend shielding the entire guitar internally with DiMarzio Shielding
Tape (EP1000). This will eliminate stray hum fields from the circuitry of your
guitar.
If you have any problems or questions, please call our tech line, (718) 816-
8112 between 12:00 PM and 5:00 PM Eastern Time or submit a request for
technical support on our website.
RESISTOR
CAPACITOR
1388 Richmond Terrace
P.O. Box 100387
Staten Island, NY 10310 USA
Tel (718) 981-9286 Tech (718) 816-8112
Fax (718) 720-5296
www.dimarzio.com
RED IS HOT
BLACK+WHITE
GREEN AND
BARE TO GROUND