DiMarzio The Angel - Manual (Page 2)

The Angel™ is a magnetic soundhole pickup designed to work with standard bronze strings,
but nickel - wound and compound strings can also be used. It will not work with nylon strings.
[FIG. 1]
The soundhole must have a minimum diameter of 3½ inches (89 mm).
INCLUDED IN THIS PACKAGE
(1) The Angel™ soundhole pickup
(1) 12 - foot (3.5 meter) cable
(1) 20 - inch (50 cm) endpin jack cable assembly
(1) 3⁄32 - inch Allen wrench
(2) self - adhesive cable retainer clips
(1) spare set of pickup mounting cushions
(1) instruction sheet
(1) warranty card
There are two ways to install The Angel™ soundhole pickup. The quick installation uses the
included 12-foot (3.5 meter) guitar cable out of the soundhole. The professional installation
(see reverse) uses the included pre-wired endpin jack.
THE ANGEL™ QUICK INSTALL
Loosen the clamp screws on both ends of the pickup top plate using a small Phillips
screwdriver until the clamps are open wide enough to mount the pickup on the top of the
guitar. [SEE FIG. 2] Then slide the pickup into the soundhole.
For small soundholes, it may be necessary to remove one or both clamps, slide
the pickup into place, and then reassemble the clamp(s) once the pickup is
correctly positioned. When reassembling the clamps, be sure they slide into the
slots molded into the pickup housing.
We recommend installing the pickup as close to the bottom edge of the fingerboard
(towards the neck) as possible.
Adjust the pickup so that it is centered in the soundhole and the pole pieces are aligned
with the strings. [SEE FIG. 3] A slight mismatch between your guitar’s string spacing and the
spacing of the pole pieces will not affect performance.
Tighten the clamp screws firmly, but do not over - tighten. Over-tightening can damage the
pickup or guitar finish.
Once the pickup is securely installed, you can plug the 12 - foot (3.5 meter) guitar cable
directly into the pickup output jack and hang the cable outside the soundhole.
The pole pieces of The Angel™ are preset for standard bronze acoustic strings (four wound
strings and two plain), but this setting is only a basic reference point. The pole pieces are
adjustable with the included 3⁄32 - inch Allen wrench to provide the best balance for your
specific guitar. Raising a pole piece will increase the output from its string, while lowering it
will decrease it.
IMPORTANT: The pole pieces have a maximum downward adjustment range. When you
encounter additional resistance at the bottom of the adjustment range, do not force the
pole piece further. This could result in permanent damage.
THE ANGEL™ PROFESSIONAL INSTALL
Remove the guitar strings before proceeding with installation.
The pre-wired endpin jack [SEE FIG. 4] requires a clean 15 ⁄32 -inch (11.9 mm) hole in the tail
block of the instrument.
IMPORTANT NOTE: If your guitar already has a hole of the correct diameter for
this endpin jack in the tail block, proceed to the paragraph below to complete
the installation of the endpin jack. If your guitar does not already have a hole
of the correct diameter for this endpin jack in the tail block, we strongly
recommend that a qualified guitar technician install the endpin jack as follows:
• Remove the existing endpin and place a piece of masking tape on the
outside of the instrument over the endpin area to prevent chipping of the
guitar finish.
• Enlarge the hole with a 15 ⁄32 -inch (11.9mm) tapered reamer, available from
Stewart-MacDonald (www.stewmac.com), part number 4323.
• Remove the masking tape and proceed with the installation.
Remove the strap nut, hex nut and one flat washer from the end of the jack assembly. There
should still be one locking washer, one flat washer, one hex nut, and a threaded barrel
remaining on the jack.
Using care to keep the washers on the jack, bring the jack down through the soundhole into
the body and insert it into the hole in the tail block.
Adjust the internal nut so that the larger threaded section of the jack remains recessed
1⁄
16
- inch (1.5 mm) below the outside surface of the instrument and most of the smaller
threaded section protrudes from the guitar.
With the jack in place, lay the remaining flat washer over the threads outside the instrument
and install the external hex nut hand tight.
Insert the included 3⁄32 - inch Allen wrench through the cross hole in the jack and hold firmly
while tightening the nut. Use of a proper wrench instead of pliers will help prevent damage
to the guitar. To avoid cracking the guitar finish, do not over-tighten the nut.
NOTE: If the jack will not tighten firmly, remove the external hex nut and re-adjust the
internal hex nut until the larger threaded section is recessed at least 1⁄
16
- inch (1.5 mm)
below the outer surface of the instrument.
Finish by installing the strap nut hand tight. It should cover the retaining nut and washer. The
end of the jack must protrude slightly from the end of the strap nut so that when a plug is
inserted, it will snap securely in place.
Once the endpin jack is installed, install two of the self-adhesive cable retainer clips on the
inner back surface of the guitar to hold down the cable and prevent it from vibrating
against the guitar.
Install the pickup by following THE ANGEL™ QUICK INSTALL instructions on the front of this
page.
Once the pickup is securely installed, plug the cable from the pre-wired endpin jack into the
pickup output jack. Restring your guitar and you’re ready to play.
1388 Richmond Terrace • PO Box 100387
Staten Island, NY 10310
www.dimarzio.com
THE ANGEL™ DP230
INSTALLATION INSTRUCTIONS − page 2
FIG. 4
Internal
Hex Nut
Flat Washer
Locking Washer
External
Hex Nut
Strap
Nut
Guitar
Tail Block
Cross
Hole