Hale HFM - Manual (Page 6)

Technical Specifications
Pump
Rated Capacities: 750,1000,
1250,1500 GPM ~ 150 PSI,
(2850, 3785, 4732, 5675 L/min
10.3 bar).
Type : Single-stage,
single-suction, gear-driven
centrifugal pump designed for
crankshaft-driven application,
with an integrated clutch for
engagement.
Impeller: Fine-grain bronze,
closed type, single-suction
mixed flow design, 10 inch (254
mm) diameter, accurately
machined and individually
balanced.
Clearance Rings: Bronze, front
and rear of impeller, easily
renewable.
Pump Shaft: Heat-treated
electric furnace
corrosion-resistant stainless
steel.
Packing: Maintenance-free,
self-adjusting mechanical seal.
Pump Casing: Fine-grain cast
iron with a minimum tensile
strength of 30,000 PSI. Tested
at 600 PSI hydrostatically by
Hale.
Suction Manifold: Fine-grain
cast iron with a minimum tensile
strength of 30,000 (206,842 kpa)
PSI. Tested at 600 PSI (41 bar),
hydrostatically and equipped
with fluid jacket for engine
coolant connection. Two 2-1/2
inch or 3 inch NPT pipe
connections are available.
Suction tube: Fine-grain cast
iron 4-1/2 inch NST (750 GPM),
5 inch NST (1000 GPM); 6 inch
NST (1250,1500 GPM).
Discharge Manifold: Fine-grain
cast iron with a minimum tensile
strength of 30,000 (206,842 kpa)
PSI tested at 600 PSI (41 bar)
hydrostatically. Designed with
six -3 inch cored openings to
accommodate discharge
requirements. Optional
manifolds available.
Discharge Valves: Hale Model
25BDT Valves (standard)
supplied as follows: three (750
GPM); four (1000,1250,1500
GPM). Hale Model 25BDT
Valves available as optional
equipment.
Gearbox
Drive Shaft: Heat-treated 1-1/4
in ten spline designed to accept
commercially available universal
joints.
Bearings: Heavy-duty ball
bearings, precision-ground to
size and lubricated from central
oil reservoir.
Gears: Both drive and pump
gears manufactured from the
highest quality steel alloy and
case hardened to provide
maximum strength and long life.
Ratios: Five ratios available to
provide maximum pump
performance and broaden
engine selection (gasoline and
diesel). Ratios: 1.40:1, 1.59:1,
1.81:1, 2.16:1, or 2.37:1.
Clutch: Integrated two-stage,
positive drive, wet-clutch design,
splash-lubricated from central
reservoir.
Mounting: Adjustable mounting
brackets provided for
standardization and to assist in
proper angularity requirements.
Pressure Control Device:
3 inch relief valve with control
standard (750,1000 and 1250
GPM); 3-1/2 inch relief valve with
control standard (1500 GPM).
Priming System: Hale Model
Electric Rotary Vane Priming
System, includes priming valve.
Meets or exceeds NFPA
1901standards.
Testing: Pump dynamometer
pretested by the Hale to ensure
compliance with NFPA 1901
standards.
Optional Accessories
Model TRV120 thermal Relief
Valve:
Automatically protects against
pump overheating.
TPM/P35 relief valve system.
Discharge and Suction Valves
Full-flow, quarter turn, ball-type with
locking handle.
Inline Valves: 1 inch through 3 inch,
full-flow, quarter turn, ball-type.
Drain Valves: Push-pull hose
bleeder valve and multi-port master
drain valve.
Strainers: Full-flow, basket-type
Shift: Air power shift system for
clutch.
Hale Products Europe
Charles Street
Warwick, CV34 5LR
England
TEL: (44) 01926 623000
FAX: (44) 01926 623666
www.haleeurope.com
Hale Products Asia
Singapore Rep. Office
63 Hillview Ave. #07-08
Lam Soom Industrial Bldg.
Singapore 669569
TEL: (65) 764-3575
FAX: (65) 764-4020
Hale Products
A Unit of IDEX Corp.
700 Spring Mill Avenue
Conshohocken, PA 19428
USA
TEL: 610/825-6300
FAX: 610/825-9615
www.haleproducts.com
Hale Products
Europe GmbH
Industriegebiet-Nord
Benzstrasse 4
64807 Dieburg Germany
TEL: (49) 06071 /92665
FAX: (49) 06071 /926677
MADE IN THE USA
Note: Hale Products Inc. cannot assume responsibility for product failure resulting
from improper maintenance or operation. Hale is responsible only to the limits stated
in the product warranty. Product specifications contained in this material are subject
to change without notice. Bulletin 482 10/00 , rev 3 ©2000 Hale Products Inc.