Philips 27PT5445-37B User Manual

Audio out l r s-video out ant/cable out video out, 12 3 vol, Video audio l r s-video video audio right left

User Manual

27PT5445/37

3121 235 22411- English

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

Do not block any of the ventilation openings. Install in accordance
with the manufacturers instructions.

Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and third grounding prong.
The wide blade or third prong are provided for your safety. When
the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.

10.

Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.

11.

Only use attachments/accessories specified by the manufacturer.

12.

Use only with a cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the appara
tus. When a cart is used, use caution when moving

the cart/apparatus combination to avoid injury from tip-over.

13.

Unplug this apparatus during lightning storms or when unused for
long periods of time.

14.

Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects
have fallen into apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.

15.

This product may contain lead and mercury. Disposal of these materi-
als may be regulated due to environmental considerations. For dispos-
al or recycling information, please contact your local authorities or
the Electronic Industries Alliance: www.eiae.org

16.

Damage Requiring Service - The appliance should be serv-
iced by qualified service personnel when:
A.

The power supply cord or the plug has been damaged; or

Objects have fallen, or liquid has been spilled into the appli-
ance; or

The appliance has been exposed to rain; or

The appliance does not appear to operate normally or
exhibits a marked change in performance; or

The appliance has been dropped, or the enclosure damaged.

17.

Tilt/Stability - All televisions must comply with recommended
international global safety standards for tilt and stability properties of
its cabinet design.
• Do not compromise these design standards by applying excessive
pull force to the front, or top, of the cabinet which could ultimately
overturn the product.
• Also, do not endanger yourself, or children, by placing electronic
equipment/toys on the top of the cabinet. Such items could unsus-
pectingly fall from the top of the set and cause product damage
and/or personal injury.

18.

Wall or Ceiling Mounting - The appliance should be
mounted to a wall or ceiling only as recommended by the manufac-
turer.

19.

Power Lines - An outdoor antenna should be located away from
power lines.

20.

Outdoor Antenna Grounding - If an outside antenna is
connected to the receiver, be sure the antenna system is grounded
so as to provide some protection against voltage surges and built up
static charges.
Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984,
provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an anten-
na discharge unit, size of grounding connectors, location of antenna-
discharge unit, connection to grounding electrodes, and requirements
for the grounding electrode. See Figure below.

21. Object and Liquid Entry - Care should be taken so that

objects do not fall and liquids are not spilled into the enclosure
through openings.comply with recommended international global safe-
ty standards for tilt and stability properties of its cabinet design.

22.

Battery Usage CAUTION - To prevent battery leakage that
may result in bodily injury, property damage, or damage to the unit:
• Install all batteries correctly, with + and - aligned as marked on
the unit.
• Do not mix batteries (old and new or carbon and alkaline, etc.).
• Remove batteries when the unit is not used for a long time.

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250, PART H)

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

Note to the CATV system installer: This
reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.

Example of Antenna Grounding
as per NEC - National Electric Code

ASIC

AND

EMOTE

ONTROL

PERATION

Press the POWER button
to turn the TV ON.

Note:You can also press any
button on the front of the TV
to turn the TV ON.

Press the VOLUME + button to
increase the sound level, or the
VOLUME – button to lower the
sound level.

Pressing both buttons at the
same time will display the on-
screen menu. Once in the menu,
use these buttons to make adjust-
ments or selections.

Press the CHANNEL UP + or
DOWN – button to select TV
channels.

Point the remote control
toward the remote sensor win-
dow on the TV when operating
the TV with the remote.

REMOTE CONTROL

o load the supplied batteries

into the remote:

1. Remove the battery com-
partment lid on the back of the
remote.

2. Place the batteries (2-AA) in
the remote. Be sure the (+) and (-
) ends of the batteries line up cor-
rectly (inside of case is marked.)

3. Reattach the battery lid.

Battery Compartment

2-AA Batteries

Battery Lid

Back of Remote

EMOTE

ONTROL

UTTON

ESCRIPTIONS

QUADRASURF Buttons
(Red, Green,Yellow, Blue) Allows you to store
and surf up to 10 channels you choose for
each colored button.

AV Button
Press to select an accessory signal input from
the front AV Inputs.

SMILEY Button
Press to add channels to the “QuadraSurf”
lists. Works with all colored buttons.

AUTO SOUND Button
Press repeatedly to choose from different fac-
tory pre-defined sound settings. Choose from
Personal (how you set the Sound Menu
options),Voice (for programming with speaking
only), Music (for musical type programs such as
concerts), or Theatre (used when watching
movies).

MENU Button
Press to display the on-screen menu. Also can
be used to back out of the on-screen menu
until it disappears from the TV’s screen.

CC Button
Press to activate the Closed Captioning
options. Repeatedly pressing the CC button
will scroll the available options on the TV
screen.

VOL(ume) + or - Buttons
Press the VOL + button to increase the TV’s
sound level. Press the VOL – button to
decrease the TV’s sound level.

MUTE Button
Press the mute button to eliminate the sound
being heard from the TV. “MUTE” will be dis-
played on the TV’s screen. Press again to
restore the TV’s volume to it’s previous level.

SLEEP Button
Press the Sleep button to set the TV to auto-
matically turn itself off after a set period of
time. Press repeatedly to select 15, 30, 45, 60,
90, 120, 180, or 240 minutes.

VOL

or French and Spanish speaking TV
owners an onscreen LANGUAGE option

is present.With the LANGUAGE control you
can set the TV’s on-screen menu to be
shown in English, French, or Spanish.

Press the MENU button on
the remote control to show the
on-screen menu.

Press the CURSOR UP ˚

˚ or

DOWN ¸

buttons to scroll

though the on-screen menu until
the word INSTALL is highlighted.

Press the CURSOR RIGHT
˙

˙button to display the
INSTALL menu features.

Press the CURSOR UP ˚

˚ or

DOWN ¸

¸buttons to scroll

through the Install features until
the word LANGUAGE is high-
lighted.

Press the CURSOR RIGHT
˙

˙button repeatedly to select
English, Francais (French), or
Español (Spanish).

When finished, press the
STATUS/EXIT button to
remove the menu from the TV’s
screen.

OW TO

SE THE

ANGUAGE

ONTROL

The Language contol only makes the
TV’s on-screen MENU items appear
in English, Spanish, or French text.
It does not change the other on-
screen text features such as Closed
Caption (CC) TV shows.

ELPFUL

INT

EMOTE

ONTROL

UTTON

ESCRIPTIONS

VOL

POWER Button
Press to turn the TV on or off.

A/CH Button (Alternate Channel)
Press to toggle between the last viewed channel
and the channel presently being viewed.

FROWNIE Button
Allows you to delete channels from the “Quadra
Surf” lists for the colored buttons.Works with all
colored buttons.

AUTO PICTURE Button
Press repeatedly to choose from 5 different facto-
ry predefined picture settings. Choose from
Personal (how you set the Picture Menu
Adjustment controls), Movies (for movies), Sports
(for any sporting event),Weak Signal (used when
the signal being received is not great), or
Multimedia (for video games).

STATUS/EXIT Button
Press to display the current channel number. If the
on-screen menu is displayed, press the Status/Exit
button of remove it from the TV’s screen.

˙, ˝

˝, ˚

˚, and

Buttons

Press to navigate, select, and adjust controls within
the on-screen menu.Also use the CURSOR ˚ or
CURSOR ¸ to activate or deactivate the
EXPAND 4:3 screen formatting control.

CH(annel) + or CH(annel)- Buttons
Press to select channels in ascending or descending
order.

NUMBERED (0-9) Buttons
Press the numbered buttons to select TV channels
or to enter certain values within the on-screen
menu. For single channel entries, press the num-
bered button for the channel you desire.The TV
will pause for a second or two before changing to
the chosen channel.

NOTE:
This button is dedicated to TIMER features within
certain TV models.This TV does not contain these
TIMER features, therefore the button will have no
functionality when pressed.

UTOMATICALLY

ROGRAM

Auto Program

Channel

Main

Picture

Sound

Features

Install

Brightness

Color

Picture

Sharpness

Tint

More...

Main

Picture

Sound

Features

Install

Language

Tuner Mode

Auto Program

Channel Edit

Install

Language

Tuner Mode

Auto Program

Channel Edit

Auto Program

Channel

Auto Program

Channel

VOL

our TV can automatically set itself for
local area (or Cable TV) channels.This

makes it easy for you to select only the TV
stations in your area when the CHANNEL
(+), (–) buttons are pressed.

Note: Make sure the antenna or cable sig-
nal connection has been completed before
AUTO PROGRAM is activated.

Press the MENU button on the
remote to show the on-screen
menu.

Press the Press the CURSOR
UP˚

˚ or DOWN ¸

¸ buttons

to scroll through the on-screen
menu until the word INSTALL is
highlighted.

Press the CURSOR RIGHT ˙

button to display the INSTALL
menu features.

Press Press the Press the
CURSOR UP˚

˚ or DOWN ¸

buttons to scroll the Install fea-
tures until the words AUTO
PROGRAM are highlighted.

Press the CURSOR RIGHT ˙

button to start the Auto Program
scanning of channels. Auto
Programming will store all available
channels in the TV’s memory then
tune to the lowest available chan-
nel when done.

When finished, press the
STATUS /EXIT button to
remove the menu from the TV’s
screen.

When CABLE is selected, channels 1-
125 are available.

When ANTENNA is selected, chan-
nels 2-69 are available.

When AUTO is selected, the TV will
automatically set itself to the correct
mode based on the type of signal it
detects when the AUTO PROGRAM
feature is activated.

Helpful Hints

OW TO USE THE

UNER

ODE

ONTROL

he TUNER MODE control allows you to

change the TV’s input signal to either

ANTENNA, CABLE, or AUTO mode. It’s
important for the TV to know what type of
signal to look for (Cable TV or an Antenna).
In the AUTO mode, when the AUTO PRO-
GRAM feature is activated, the TV will auto-
matically choose the correct mode.

Press the MENU button on the
remote to show the on-screen
menu.

Press the CURSOR UP ˚

˚ or

DOWN ¸

buttons to scroll

through the on-screen menu until
the word INSTALL is highlighted.

Press the CURSOR RIGHT ˙

button to display the INSTALL
menu features.

Press Press the CURSOR UP

˚ or DOWN ¸

buttons to

scroll the Install features until the
words TUNER MODE is high-
lighted.

Press the CURSOR RIGHT˙

button to select either ANTEN-
NA, CABLE, or AUTO mode.

When finished, press the STA-
TUS /EXIT button to remove
the on-screen menu from the TV’s
screen.

Main

Picture

Sound

Features

Install

Brightness

Color

Picture

Sharpness

Tint

More...

Main

Picture

Sound

Features

Install

Language

Tuner Mode

Auto Program

Channel Edit

Install

Language

Tuner Mode

Auto Program

Channel Edit

English

Antenna

Install

Language

Tuner Mode

Auto Program

Channel Edit

English

Cable

Install

Language

Tuner Mode

Auto Program

Channel Edit

English

Auto

VOL

When CABLE is selected, channels 1-
125 are available.
When ANTENNA is selected, chan-
nels 2-69 are available.
When AUTO is selected, the TV will
automatically set itself to the correct
mode based on the type of signal it
detects when the AUTO PROGRAM
feature is activated.

Helpful Hints

HANNEL

DIT

Channel Edit

Channel No.

Skipped

Main

Picture

Sound

Features

Install

Brightness

Color

Picture

Sharpness

Tint

More...

Main

Picture

Sound

Features

Install

Language

Tuner Mode

Auto Program

Channel Edit

Install

Language

Tuner Mode

Auto Program

Channel Edit

Channel No.

Skipped

Channel Edit

Channel No.

Skipped

Channel Edit

Channel No.

Skipped

Off

VOL

An “X” appearing in front of
any channel will indicate that
channel has skip on.When the
CH + or CH - buttons are
used, those channels will be
skipped.

ELPFUL

INTS

hannel Edit makes it easy for you to ADD or
DELETE channels from the list of channels

stored in the TV’s memory.

Press the MENU button on the
remote control to show the on-screen
menu.

Press the CURSOR UP ˚

˚ or

DOWN ¸

¸ buttons to scroll though

the on-screen menu until the word
INSTALL is highlighted.

Press the CURSOR RIGHT ˙

button to display the INSTALL
menu features.

Press the CURSOR UP ˚

˚ or

DOWN ¸

¸ buttons to scroll

through the Install features until the
words CHANNEL EDIT are high-
lighted.

Press the CURSOR RIGHT ˙

button to display the CHANNEL
EDIT options.

With the CHANNEL EDIT
options displayed, and CHANNEL
NO. highlighted; you can use the cur-
sor buttons to scroll through all avail-
able channels that you wish to add
(skipped OFF) or delete (Skipped ON)
from the TV’s memory.You can also
use the NUMBERED buttons to go
directly to a specific numbered chan-
nel that you want to add or skip. Or,
you can also use the CH+ or CH- to
quickly scan through the channels that
have not been skipped.

Using the CURSOR DOWN ¸

button, scroll the menu to highlight the
word SKIPPED.

Now use the CURSOR RIGHT

to toggle between ON or

OFF. If ON is selected the channels
is skipped when scrolling channels
with the CH+ or CH- buttons. If OFF
is selected the channels is not skipped
when scrolling channels with the CH+
or CH- buttons.

When finished, press the
STATUS/EXIT button to remove
the menu from the screen.

ANEL

NDEX

CO VER

SAFETY

INFO

MODEL

REGISTRATION
INFORMATION

PANEL

Panel

Sequence

and

Panel Inde

LIMITED

WARRANTY

PANEL

Side 1

Side 2

Subject

Panel No.

Antenna Basic Connection . . . . . . . . . . .1
Audio/Video Connections

AV Input Jacks . . . . . . . . . . . . . . . . . . . .4

Component Video Input Jacks . . . . . . . .7
Front (Side) Audio/Video Input Jacks . . .5
Headphone Jack . . . . . . . . . . . . . . . . . .5

AV Output Jacks . . . . . . . . . . . . . . . . . .8

S-Video Input Jacks . . . . . . . . . . . . . . . .6

AutoLock™ Controls

Access Code . . . . . . . . . . . . . . . . . . . .19

Block All Channels . . . . . . . . . . . . . . . .21
Block Channels . . . . . . . . . . . . . . . . . .20
Clear All Blocked Channels . . . . . . . . .21
Movie Ratings . . . . . . . . . . . . . . . . . . .22
Other Blocking Options . . . . . . . . . . .24

TV Ratings . . . . . . . . . . . . . . . . . . . . . .23

Understanding AutoLock™ . . . . . . . . .18

Automcatically Programming TV . . . . . .13

Subject

Panel No.

AutoPicture™ Control . . . . . . . . . . . . .26
AutoSound™ Control . . . . . . . . . . . . . .26
Basic Remote Operation . . . . . . . . . . . . .3
Basic Television Operation . . . . . . . . . . . .3
Cable Box Connection . . . . . . . . . . . . . .2
Channel Edit . . . . . . . . . . . . . . . . . . . . .14
Closed Captioning . . . . . . . . . . . . . . . . .25
Format Controls . . . . . . . . . . . . . . . . . .17
Language Controls . . . . . . . . . . . . . . . . .11
Limited Warranty . . . . . . . . . . . . . . . . . .30
Picture Menu Controls . . . . . . . . . . . . .15
QuadraSurf™ . . . . . . . . . . . . . . . . . .27-28
Remote Batteries . . . . . . . . . . . . . . . . . .3
Remote Control Button Descriptions 9-10
Sleeptimer . . . . . . . . . . . . . . . . . . . . . . .25
Sound Menu Controls . . . . . . . . . . . . . .16
Tuner Mode . . . . . . . . . . . . . . . . . . . . . .12
Troubleshooting . . . . . . . . . . . . . . . . . . .29

ANEL

AYOUT

ASIC

NTENNA AND

ABLE

ONNECTIONS

our home’s signal input might come from
a single (75 ohm) round cable, a

Converter Box, or from an antenna. In either
case the connection to the TV is very easy.

If your Cable TV signal or
Antenna signal is a round cable
(75 ohm) then you're ready to con-
nect to the TV.
If your antenna has flat twin-
lead wire (300 ohm), you first need
to attach the antenna wires to the
screws on a 300 to 75 ohm adapter.
If you have a Cable Converter
Box: Connect the Cable TV signal
to the Cable Signal IN(put) plug on
the Converter.

Connect the Cable TV cable or
Antenna cable (or 300 to 75 ohm
adapter) to the 75

Ω plug on the TV.

If you have a Cable Converter
Box: Connect the OUT(put) plug
from the Converter to the 75

Ω plug

on the TV.

After using the AutoProgram Control,
press the CH + and – buttons to
scroll through all the channels stored
in the television’s memory.

ELPFUL

INT

75‰

S-VIDEO

VIDEO

AUDIO

CVI

AV out

AV in

Back of TV

Cable signal

coming from

Cable Company

Jack Panel Back of TV

⍀

75‰

S-VIDEO

VIDEO

AUDIO

CVI

AV out

AV in

Antenna Connection

300 to 75

Ω

Adapter

Combination

VHF/UHF Antenna

(Outdoor or Indoor)

Twin Lead

Wire

Round Cable

Ω

Back of TV

Direct Cable Connection

Ω Round

Coaxial Cable

TV/VCR

CABLE

USB

DVD-D OUT

AUDIO IN

SPDIF

VIDEO

IN OUT

S-VIDEO

R L

AUDIO OUT

PASSCARD

Y Pb Pr

OPTICAL

SPDIF

75Ω

S-VIDEO

VIDEO

AUDIO

CVI

AV out

AV in

L/Mono

VIDEO

S-VIDEO

CVI

COMPONENT VIDEO INPUT

AUDIO

AV In

AV Out

ABLE

ONNECTIONS

f you cable signal uses a cable box or
decoder, follow the easy steps below to com-

plete the connection.

Cable Box (w/RF In/Outputs):
This connection will be mono.

Connect the Cable Company
supplied cable to the signal IN(put)
plug on the back of the Cable Box.

Using a separate round coaxial cable,
connect one end to the OUT(put)
(TO TV) plug on the back of the
Cable Box.

Connect the other end of the
round coaxial cable to the 75

Ω

input on the back of the television.
Screw it down finger tight.

NOTE: If applicable, set the OUTPUT
CHANNEL SWITCH on the back of the
cable box to CH 3 or 4.Tune the TV to the
same channel and change channels at the
cable box. In some cases, the cable box will
automatically tune to either channel 3 or 4,
change channels until the picture appears.
Cable Box (w/Audio/Video Outputs):
This connection will supply Stereo sound.

Connect the Cable Company
supplied cable to the cable signal
IN(put) plug on the back of the
Cable Box.

Using a RCA type Video Cable, con-
nect one end of the cable to the
Video (or ANT, your cable box may be
labeled differently) Out jack on the
cable box and the other end to the
AV1 Video Input on the TV.

Connect one end of the Audio Left
and Right Cable to the left and
right Audio Out L & R jacks on
the cable box. Connect the other
end to the AV In Audio L & R Input
jacks on the TV.

NOTE: Use the AV button on the TV
remote control to tune to the AV channel
for the cable box signal. Once tuned, change
channels at the cable box, not the television.

75‰

S-VIDEO

VIDEO

AUDIO

CVI

AV out

AV in

⍀

TV/VCR

CABLE

USB

DVD-D OUT

AUDIO IN

SPDIF

VIDEO

IN OUT

S-VIDEO

R L

AUDIO OUT

PASSCARD

Y Pb Pr

OPTICAL

SPDIF

Jack Panel Back of Cable Box

Cable Signal IN from the

Cable Company

Round 75

Ω

Coaxial Cable

Jack Panel Back of TV

Cable Signal IN
from the Cable

Company

Cable Box with A/V Outputs

Jack Panel Back of TV

Audio Cables

L (White) & R (Red)

Video Cable

(Yellow)

Cable Box (w/RF In/Outputs):

Cable Box (w/Audio/Video Outputs):

AV (A

UDIO

IDEO

) O

(

PUT

) C

ONNECTIONS

he Audio/Video Output jacks are great for
recording with a VCR or used to connect

an external audio system for better sound
reproduction.

AUDIO SYSTEM CONNECTION:

Connect one end of the R(ight)
and L(eft) AUDIO jacks on the
TV to the R and L audio input jacks
on your amplifier or sound system.
Set the audio system’s volume to a
normal listening level.

Turn the TV and audio system
ON. To adjust the volume on the
audio system, you will need to
change the volume at the external
audio system, not the television.

SECOND VCR CONNECTION:

NOTE: Refer to panel number 4 for the
proper hookup of the first VCR. Follow
the instructions on how to tune to the
AV

1 channel to view a pre-recorded tape.

The following steps allow you to
connect a second VCR to record the
program while your watching it.

Connect one end of the yellow
Video Cable to the AV Out VIDEO
plug. Connect the other end to the
VIDEO IN plug on the second VCR.

Connect one end of the red and
white Audio cable from the AV
Out AUDIO L and R plugs on the
TV to the AUDIO IN plugs on the
VCR.

Turn the Second VCR ON,
insert a VHS tape and it’s ready to
record what’s being viewed on the
TV screen.

L/Mono

VIDEO

S-VIDEO

CVI

COMPONENT VIDEO INPUT

AUDIO

AV In

AV Out

AUX/TV INPUT

PHONO INPUT

Back of TV

Audio Cables

(Red and White)

L/Mono

VIDEO

S-VIDEO

CVI

COMPONENT VIDEO INPUT

AUDIO

AV In

AV Out

ANTENNA

OUT

ANTENNA

VIDEO

AUDIO

OUT

ANTENNA

OUT

ANTENNA

VIDEO

AUDIO

OUT

Back of TV

Audio Cables

1st VCR

(refer to panel 4 for

proper connection)

Video
Cable

2nd VCR with Audio and

Video Input Jacks

SECOND VCR CONNECTION:

AUDIO SYSTEM CONNECTION:

OMPONENT

IDEO

(CVI) I

NPUT

ONNECTIONS

omponent Video inputs provide for the
highest possible color and picture resolu-

tion in the playback of digital signal source
material, such as with DVD players. The
color difference signals (Pb, Pr) and the
luminance (Y) signal are connected and
received separately, which allows for
improved color bandwidth information (not
possible when using composite video or S-
Video connections).

Connect the Component (Y, Pb,
Pr) Video OUT jacks from the
DVD player (or similar device) to the
(Y, Pb, Pr) in(put) jack on the TV.
When using the Component Video
Inputs, it is best not to connect a sig-
nal to the AV in Video Jack.

Connect the red and white
AUDIO CABLES to the Audio
(left and right) output jacks on the
rear of the accessory device to the
Audio (L and R) AV In Input Jacks
on the TV.

Turn the TV and the DVD (or
digital accessory device) ON.

Press the AV button or the CH
+ or CH – buttons to scroll the
available channels until CVI appears
in the upper left corner of the TV
screen.

Insert a DVD disc into the DVD
player and press the PLAY

ᮣ

button on the DVD Player.

The description for the component video con-
nectors may differ depending on the DVD player
or accessory digital source equipment used (for
example,Y, Pb, Pr;Y, B-Y, R-Y;Y, Cr, Cb). Although
abbreviations and terms may vary, the letters b
and r stand for the blue and red color compo-
nent signal connectors, and Y indicates the lumi-
nance signal. Refer to your DVD or digital
accessory owner’s manual for definitions and
connection details.

ELPFUL

INT

L/Mono

VIDEO

S-VIDEO

CVI

COMPONENT VIDEO INPUT

AUDIO

AV In

AV Out

VOL

S-VIDEO

OUT

AUDIO

VIDEO

COMP VIDEO

Componen

t Video
Cables

(Green,

Blue, Red)

Audio

Cables
(Red &
White)

Accessory Device

Equipped with

Component Video

Outputs

Back of TV

NOTE: When using additional accessories, only one
external source will be audible, as there is only one
set of sound inputs. Component Video (CVI) input
will dominate over all other inputs, including S-Video
(S-VHS) and AV. When S-Video (S-VHS) is used, it
will dominate over the AV input.

S-V

IDEO

(S-V

) I

NPUT

ONNECTIONS

he S(uper)-Video connection on the rear
of the TV can provide you with better pic-

ture detail and clarity for the playback of
accessory sources such as DBS (digital broad-
cast satellite), DVD (digital video discs), video
games, and S-VHS VCR (video cassette
recorder) tapes than the normal antenna pic-
ture connections.

NOTE: The accessory device must have an
S-VIDEO OUT(put) jack in order for you to
complete the connection on this page.

Connect one end of the S-
VIDEO CABLE to the S-VIDEO
jack on the back of the TV.Then con-
nect one end the AUDIO (red and
white) CABLES to the AV In AUDIO
L and R (left and right) jacks on the
rear of the TV.

Connect other end of the S-
VIDEO CABLE to the S-VHS (S-
Video) OUT jack on the back of the
VCR.Then connect the other ends
of the AUDIO (red and white)
CABLES to the AUDIO (left and
right) OUT jacks on the rear of the
VCR.

Turn the VCR and the TV ON.

Press the AV button or the CH
+ or CH – buttons on the remote
to scroll the channels until SVHS
appears in the upper left corner of
the TV screen.

Now your ready to place a prere-
corded video tape in the VCR and
press the PLAY

ᮣ button.

L/Mono

VIDEO

S-VIDEO

CVI

COMPONENT VIDEO INPUT

AUDIO

AV In

AV Out

VOL

AUDIO OUT

L R

S-VIDEO

OUT

ANT/CABLE

OUT

VIDEO

OUT

VCR or External

Accessory

Device

(with S-Video

Output)

Audio

Cables
(Red &
White)

S-Video

Cable

Back of TV

IDE

AV C

ONNECTIONS

udio and Video Side Inputs are available
for a quick connection of a VCR, to play-

back video from a camera, or attach a gam-
ing device. Use the AV button on the remote
control to tune these inputs.

Connect the video (yellow)
cable from the Video output on
the Camera (or accessory device)
to the Video (yellow) Input located
on the SIDE of the TV.

For Stereo Devices: Connect the
audio cable (red and white) from
the Audio Left and Right Outputs
on the Camera to the Audio In
(white) jack on the SIDE of the tel-
evision.

For Mono Devices: Connect one
end of the audio cable from the
Audio Out jack on the device to
the Audio In (white) jack on the
SIDE of the television.

Turn the TV and the accessory
device ON.

Press the AV button on the
remote control to tune the TV to
the side (or front) input jacks. “AV”
will appear on the TV screen.

Press the PLAY

ᮣ button on

the accessory device to view play-
back, or to access the accessory
device (camera, gaming unit, etc.).

Model No.:

Serial No.:

Return your Product Registration Card today

to get the very most from your purchase.

Registering your model with PHILIPS makes you eligible for all of the valuable benefits listed
below, so don't miss out. Complete and return your Product Registration Card at once to ensure:

*Proof of
Purchase

Returning the enclosed card guar-
antees that your date of purchase
will be on file, so no additional
paperwork will be required from
you to obtain warranty service.

*Product Safety

Notification

By registering your product,
you'll receive notification -
directly from the manufacturer -
in the rare case of a product
recall or safety defect.

*Additional Benefits of
Product Ownership

Registering your product guaran-
tees that you'll receive all of the
privileges to which you're enti-
tled, including special money-sav-
ing offers.

Congratulations on your purchase,
and welcome to the “family!”

Dear PHILIPS product owner:

Thank you for your confidence in PHILIPS.You’ve
selected one of the best-built, best-backed products
available today.We’ll do everything in our power to
keep you happy with your purchase for many years to
come.

As a member of the PHILIPS “family,” you’re entitled to
protection by one of the most comprehensive war-
ranties and outstanding service networks in the indus-
try.What’s more, your purchase guarantees you’ll
receive all the information and special offers for which
you qualify, plus easy access to accessories from our
convenient home shopping network.

Most importantly, you can count on our uncompromis-
ing commitment to your total satisfaction.

All of this is our way of saying welcome - and thanks
for investing in a PHILIPS product.

P.S. To get the most from your PHILIPS
purchase, be sure to complete and return
your Product Registration Card at once.

Visit our World Wide Web Site at http://www.usasupport.philips.com

Know these

safety

symbols

C A U T I O N

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This “bolt of lightning” indicates unin-
sulated material within your unit may
cause an electrical shock. For the safe-

ty of everyone in your household, please do
not remove product covering.

The “exclamation point” calls attention
to features for which you should read
the enclosed literature closely to pre-

vent operating and maintenance problems.
WARNING: To reduce the risk of fire or
electric shock, this apparatus should not be
exposed to rain or moisture and objects filled
with liquids, such as vases, should not be
placed on this apparatus.
CAUTION: To prevent electric shock, match
wide blade of plug to wide slot, fully insert.
ATTENTION: Pour éviter les choc élec-
triques, introduire la lame la plus large de la
fiche dans la borne correspondante de la
prise et pousser jusqu’au fond.

For Customer Use

Enter below the Serial No. which is located
on the rear of the cabinet. Retain this
information for future reference.
Model No. __________________________
Serial No. __________________________

2 3

VOL

VIDEO

AUDIO

S-VIDEO

VIDEO

AUDIO

RIGHT LEFT

VOL

Jack Panel of

Accessory

Device

Optional

Headphones

Audio

Cables

Video
Cable

AV (A

UDIO

IDEO

) I

NPUT

ONNECTION

he TV’s audio/video input jacks are for
direct picture and sound connections

between the TV and a VCR (or similar device)
that has audio/video output jacks. Follow the
easy steps below to connect an accessory
device to the AV In Input Jacks located on the
back of the TV.

Connect the VIDEO (yellow)
cable to the VIDEO AV In jack on
the back of the TV.

Connect the AUDIO (red and
white) cables to the AUDIO (left
and right) AV In jacks on the rear of
the TV.

Connect the VIDEO (yellow)
cable to the VIDEO OUT jack on the
back of the VCR.

Connect the AUDIO (red and
white) cables to the AUDIO (left
and right) OUT jacks on the rear of
the VCR.

Turn the VCR (accessory device)
and the TV ON.

Press the AV button on the
remote control to select the AV chan-
nel.AV will appear in the upper left
corner on the TV screen.

With the VCR (or accessory device)
ON and a prerecorded tape (CD,
DVD, etc.) inserted, press the PLAY
ᮣ button to view the tape on the
television.

All the AV channels can be selected by
pressing the Channel + or – buttons.
The AV channels can also be added to
the QuadraSurf™ buttons for quick
access.

ELPFUL

INT

S-VIDEO

ANTENNA

OUT

ANTENNA

VIDEO

AUDIO

OUT

VOL

VIDEO

AV In

AV Out

AUDIO

CVI

Video Cable

(Yellow)

Audio Cables

(Red & White)

Back of TV

Back of Typical VCR

VCR with

Audio/Video Outputs

Thank you for choosing Philips.

Need help fast?

Read your Quick Use Guide and/or
Owner's Manual first for quick tips

that make using your Philips product

more enjoyable.

If you have read your instructions

and still need assistance,

you may access our online help at

www.usasupport.philips.com

or call

1-888-PHILIPS (744-5477)

while with your product

(and Model / Serial number)

ARRÊT

ALTO

STOP

This manual is related to the following products:

27PT5445-37