Philips PR0935B - Manual (Page 7)

F
EATURES
(C
ONT
’
D
)
G LOSSARY
- 7 -
T o adjust your TV picture
controls, select a channel
and follow these steps.
P ICTURE
A DJUSTMENTS Press the MENU
button, then press the
CH(annel) ▲ or ▼ button
to select a control.
Press the VOL(ume)
B /{ buttons to adjust the
selected picture control.
BRIGHTNESS Press the VOL(ume) B/{ buttons
until the darkest parts of the picture are as bright as
you prefer.
COLOR Press the VOL(ume) B/{ buttons to add
or reduce color.
PICTURE Press the VOL(ume) B/{ buttons until
the lightest parts of the picture show good detail.
SHARPNESS Press the VOL(ume) B/{ buttons
to improve detail in the picture.
TINT Press the VOL(ume) B/{ buttons to obtain
natural skin tones.
Press the
STATUS/EXIT button.
T his feature enables you to
receive FM radio stations.
FM M ODE
Press the FM button on
the remote control to
select the FM mode. The
current radio frequency
appears on the TV screen.
The radio frequency indicator
will move or shift while on the
TV screen during normal FM
mode operation.
FM M ODE
Press the CH(annel)
▲/▼ buttons until your
desired radio frequency
appears.
FM 88.0MHz
To exit FM mode and
return to TV mode, press
the FM button.
SETUP B
EXIT B
BRIGHTNESS 24
COLOR 31
PICTURE 31
3 2 1
6 5 4
9 8 7
0
STATUS/EXIT
ALT. CH FM
MENU MUTE
VOL. VOL.
CH.
CH.
3 2 1
6 5 4
9 8 7
0
POWER
STATUS/EXIT
ALT. CH FM
SLEEP TV/AUX
MENU MUTE
VOL. VOL.
CH.
CH.
Coaxial Cable - A single cable with a metal connector that screws (or pushes) direct-
ly onto a 75
Ω
jack (ANT(enna) In jack) on the Television or VCR.
Display - Allows the user to quickly confirm the current channel number.
Menu - An on-screen listing of features that are available for adjustments.
On-screen Displays - The wording or messages that help you set up features.
Programming - Adding or deleting channels in the television’s memory. The televi-
sion “remembers’’ only the locally available or desired channel numbers and skips over
any unwanted ones.
Remote Sensor - An area on the front of the TV through which remote control sig-
nals are received.
Twin Lead Wire - The two-strand 300 Ω antenna wire used with many indoor and
outdoor antenna systems. In many cases, this type of antenna wire requires an
additional adapter (or balun) in order to connect to the ANT(enna) In jack on the TV.
Volume Indicator - Appears on the TV screen when you adjust the volume.
If you receive a weak radio signal, you may switch between the TV’s internal and external
antennas. Usually, the internal antenna of the TV best allows you to receive FM stations.
To switch between the external (EXT) and internal (INT) antennas, follow these steps.
1) Press the FM button to exit the FM mode and return to TV mode.
2) Press the MENU button.
3) Press the CH(annel) ▲ or ▼ button to select SETUP.
Then, press the VOL(ume) B or { button to continue.
4) Press the CH(annel) ▲ or ▼ button to select FM ANTENNA.
Then, press the VOL(ume) B or { button to select INT or EXT.
5) Press the STATUS/EXIT button.
If you turn off
the TV in FM mode, the
TV will be in TV mode
when you turn on the
TV again.
You may get better FM
reception by reposition-
ing the TV (when you
are using the TV’s
internal antenna).
The TV’s FM radio has
a built-in antenna with a
band range of 88.0 ~
108.0MHz. Radio sta-
tions may refer to this
number as their fre-
quency.
S MART
H ELP