Philips PR0935B - Manual (Page 5)

- 5 -
AUDIO VIDEO EARPHONE MENU VOLUME CHANNEL POWER
MENU VOLUME CHANNEL POWER
S
ETTING
U
P AND
U
SING
Y
OUR
TV
Be sure to connect the
TV power cord.
Press the POWER button to
turn on the TV.
Press the VOLUME
▲/▼ buttons to adjust the
sound level.
Press the CHAN-
NEL ▲/▼ buttons to select
available TV channels. (See
Auto Install.)
T ELEVISION
The current
channel number
will appear briefly
when first turning on
the TV and when
changing channels.
Press STATUS/EXIT
to see the channel
number on the TV
screen for five sec-
onds.
You can turn on the
TV by pressing the
CHANNEL ▲ or ▼
button on the front
of the TV. The
CH(annel) ▲/▼ but-
tons of the remote
control will not turn
on the TV power.
S MART
H ELP
Note:
• You can connect earphones (not supplied)
to the EARPHONE jack on the front of
the TV for private, personal listening.
Press the MENU button
to display the TV’s on-screen
menu.
Press the CHANNEL ▲/▼
buttons to select an item in the
menu.
Press the VOLUME ▲/▼ but-
tons to adjust an item in the
menu or to advance to the next
menu.
Note: To remove the menu,
press the CHANNEL ▲/▼ but-
tons to select EXIT. Then, press
the VOLUME ▲ or ▼ button.
(You may need to select EXIT
repeatedly to completely remove
all of the menus.)
Or, press the MENU button,
repeatedly if necessary, to
remove the on-screen menu.
Remote Sensor
Point the remote
control here
when using it to
work the TV.
A UTO I NSTALL
F ollow these steps to quickly
add area channels into the
TV’s memory. Before you
begin, make sure batteries are
in the remote control and you
are familiar with the remote.
Press the CH(annel) ▲ or
▼ button to select AUTO
INSTALL.
Then, press the VOL(ume) B
or { button to enter AUTO
INSTALL, which will set up the
channels.
When setup is complete, the
SETUP menu will reappear for
about 30 seconds, then the low-
est stored channel will appear.
Now, when you press the
CH(annel) ▲ or ▼ button, you
will only scan through channels
that are available. You still may
select non-memorized channels
by pressing the Number buttons.
Press the POWER
button to turn on the TV.
Make sure you are not in A/V
IN mode. (Press the TV/AUX
button so that A/V IN does not
appear on the screen.)
3 2 1
6 5 4
9 8 7
0
POWER
STATUS/EXIT
ALT. CH FM
SLEEP TV/AUX
MENU MUTE
VOL. VOL.
CH.
CH.
Press the MENU but-
ton. The main menu appears
on the TV screen.
SETUP B
EXIT B
BRIGHTNESS 24
COLOR 31
PICTURE 31
3 2 1
6 5 4
9 8 7
0
POWER
STATUS/EXIT
ALT. CH FM
SLEEP TV/AUX
MENU MUTE
VOL. VOL.
CH.
CH.
R EMOTE
T o load the batteries into the
remote:
1. Slide off the battery
compartment lid on the
bottom of the remote
control.
2. Insert two AA batter-
ies (supplied) into the
battery compartment
as indicated inside the
compartment. Installing
batteries incorrectly may
damage the remote
control.
3. Replace the lid.
When operating the TV with
the remote, point the remote
toward the sensor on the TV.
(See Television illustration below.)
MENU Button
Press to access or remove the on-screen menu.
Press the CH(annel) ▲/▼ buttons to select an
item in the menu. Press the VOL(ume) B/{
buttons to adjust an item in the menu or to
advance to the next menu.
Number Buttons
Press to select channels.
• Cable Users
Enter channel numbers as a two-digit number for
the quickest results. For example, to select chan-
nel 6, press 0,6. (Pressing only Number button 6
will cause a brief delay. There also may be a brief
delay when you select channels 10, 11, and 12.)
For channels 100 and above, enter three-digit
numbers. For example, to select channel 117,
press 1, 1, 7.
• Antenna Users
Enter channel numbers as a two-digit number for
the quickest results. For example, to select chan-
nel 5, press 0,5. Pressing only the Number 5 but-
ton will cause a delay in selecting channel 5. Only
channels 2-69 are available.
MUTE Button
Press to disable the sound in TV mode and FM
mode. Press again to restore the sound.
CH(annel) ▲/▼ Buttons
Press to scan through available channels. Press to
select an item in the on-screen menu. When in
FM mode, press to select an FM radio station.
STATUS/EXIT Button
Press to see the current channel number on the
TV screen.
Press to remove the on-screen menu. You also
may remove the menu by pressing the
CH(annel) ▲/▼ buttons to select EXIT, then
pressing the VOL(ume) B/{ buttons. (You
may need to select EXIT repeatedly to com-
pletely remove all of the menus.) Or, press the
MENU button repeatedly to remove all the
menus.
POWER Button
Press to turn the TV on and off.
SLEEP Button
Press to set the TV to turn itself off automati-
cally. Details are on page 6.
TV/AUX Button
Press to select A/V IN mode (for viewing tape
playback at the TV from a VCR or camcorder).
Press again to return to TV channels. Details are
on page 4.
ALT. CH (Alternate Channel) Button
Press to return to the previously viewed TV
channel.
Battery
Compartment
Lid
Battery
Compartment
VOL(ume) B/{ Buttons
Press to adjust the TV sound level in TV mode
and FM mode. Press to adjust an item in the
on-screen menu or to advance to the next
menu.
FM Button
Press to select FM mode. Press again to return
to TV mode. Details are on page 7.
Press the CH(annel) ▲
or ▼ button to select SETUP.
Then, press the VOL(ume)
B
or { button to continue
to the SETUP menu.
VOLUME 13
SLEEPTIMER OFF
SETUP B
EXIT B
BRIGHTNESS 24
EXIT B
LANGUAGE ENG
AUTO INSTALL B
CHANNEL EDIT B
FM ANTENNA INT
AUTO STORE 31
Complete each
step within 30 sec-
onds of the previ-
ous step.
S MART
H ELP