Philips 36RF82S - Manual (Page 2)

Ⅲ
2
B
ASIC
TV
AND
R
EMOTE
O
PERATION
Y our television has a set of controls located on the top of
the cabinet for use when the remote control is not needed.
1 Press the POWER button to turn the TV ON.
Note: The time it takes the TV to startup can be affected
by the AutoChron™ feature (page 4). With AutoChron ON,
the TV will search for a PBS channel to set the clock
before powering itself on. This can take several seconds.
2 Press the VOLUME (+) button to increase the sound
level or the VOLUME (–) button to lower the sound level.
Pressing both buttons at the same time will display the
onscreen menu. After you are in the menu, use these buttons
to make adjustments or selections.
3 Press the CHANNEL – (down) or + (up) button to select
TV channels. Use these buttons to make adjustments or
selections in the onscreen menu.
There is also a set of Audio and Video Input jacks located on the
side of the television cabinet. This jack panel also contains a S-video
and headphone jack. These jacks are great for connecting a video
camcorder or any accessory device that will only be hooked up tem-
porarily.
T
ELEVISION
1
3
+ – VOLUME + – CHANNEL
2
Remote Sensor Window
Audio, Video, S-Video
and Headphone Jacks
located on the side of
the television.
Volume and Channel buttons are located
on the top of the television cabinet.
T o load the supplied batteries into the remote:
1 Remove the battery compartment door on the back of
the remote.
2 Place the batteries (2-AA) in the remote. Be sure the (+)
and (–) ends of the batteries line up correctly (the inside of
the case is marked).
3 Reattach the battery compartment door.
Be sure to point the remote at the Remote Sensor window on the
front of the television when using the remote control to operate the
television.
R
EMOTE
C
ONTROL
B
ATTERIES
Remote Control
(shown from the bottom)
Battery Compartment Door
2 “AA” Batteries
Battery Compartment
R
EMOTE
C
ONTROL
B
UTTONS
Sleep Button
Press to set the TV to automatically turn itself OFF. Choose 15, 30, 45,
60, 90, 120, 180, or 240 minutes.
TV/VCR (A/CH) Button
TV/VCR – Press while in the VCR mode (the VCR indicator on the
front of the VCR will light) to view the playback of a tape. Press again to
place in the TV position (the VCR indicator light will go off) to view one
program while recording another program.
A/CH – Press to toggle between the currently viewed channel and the
previously viewed channel.
TV/VCR/ACC Mode Switch
Slide to the TV position to control TV functions, to the VCR position to con-
trol VCR functions, or to the ACC position to control the functions of acces-
sory devices (a cable converter, DBS, or DVD, for example).
Number Buttons
Press the number buttons to select TV channels. When selecting single-
digit channels, press the number of the desired channel. The TV will
pause for a few seconds and then tune to the selected channel. (Note:
You can press 0, then the number also.) For channels 100 and above,
first press 1 then the next two numbers of the desired channel.
Sound Button
Press to select an AutoSound™ control. Choose from three factory-set
controls (VOICE, MUSIC, and THEATRE) and a PERSONAL control
that you set according to your own preferences through the onscreen
Sound menu. The three factory-set controls will tailor the TV sound so
as to enhance the particular type of program you are watching.
Menu Button
Press for the onscreen menu to appear. Pressing the menu button after
menu selections are made will eliminate the menu from the display.
Cursor Buttons (Left, Right, Up, Down)
Press these buttons to highlight, select, and adjust items on the TV's
onscreen menu.
Volume (+) or (–) Buttons
Press to adjust the TV sound level.
Source Button
Press repeatedly to select the different signal sources connected to the
A/V inputs on the TV.
Status/Exit Button
Press to see the current channel number on the TV screen. Also press to
clear the TV screen after control adjustments.
Incr. Surr. (Incredible Surround) Button
Press to to set the desired Incredible Surround mode.
Program List Button
Press to display a list of channel numbers and their names (see the
“Tuner,” “Auto Program,” “Channel Edit,” and “Name” sections on
pages 3 and 4 for proper setup). Each channel will appear as a selec-
table menu item. The current channel will be highlighted by default.
Only five channels will be shown onscreen at one time; use the CUR-
SOR UP or DOWN buttons to scroll the list.
Power Button
Press to turn the TV ON and OFF.
PIP Buttons
Press to operate Picture-In-Picture features. See the PIP section in the
Instructions for Use manual for details.
Light Button
Press to back-light the buttons on the remote control.
Picture Button
Press to select an AutoPicture™ control. Choose from four factory-set
controls (MOVIES, SPORTS, WEAK SIGNAL, and MULTI MEDIA)
and a PERSONAL control that you set according to your own prefer-
ences through the onscreen PICTURE menu. The four factory-set con-
trols will tailor the TV picture so as to enhance the particular type of
program you are watching, or to improve the picture of a program that
has a weak signal.
Active Control Button
Press repeatedly to toggle the Active Control to ON or OFF. When ON,
the sharpness and noise reduction will be continuously monitored.
Mute Button
Press to turn the TV sound OFF. Press again to return the sound to its
previous level.
Channel (+) or (–) Buttons
Press to change the tuned channel.
CC/REC • Button
CC: Press to select Closed Captioning options within the menu. (See
the Instructions for Use manual for details.)
REC: Press the REC • button and the Play
ᮣ button together to start a
VCR recording.
Clock Button
Press the CLOCK button to access the onscreen Clock menu.
Surf Button
Press to select previously viewed channels. You can place up to 10 chan-
nels in memory. Then by pressing the SURF button you can quickly view
the select channels. (See the “Using the Channel Surf Control” section in
your Instructions for Use manual to see how to select a series of channels
using the Surf button.)
VCR
ᮤᮤ, ■, ᮣ, ᮣᮣ, •, II Buttons
Press to rewind, stop, play, fastforward, record, or pause/freeze a video-
tape.
Tuner A/B Button
Press to select the signal coming from the ANT IN A or ANT IN B con-
nection.
Power ON LED