Philips FWC250 - Manual (Page 16)

3139 115 20353 (ENG)
16
5 Press PROGRAM to store the
track.
• Repeat steps 3 to 5 to store other
discs and tracks.
6 Press Ç once to end programming.
™ The total number of tracks
programmed and total playing
time appear on the display.
Notes:
– If the total playing time is more than
“ 99:59“ or if one of the programmed
tracks has a number greater than 30,
then “
--:--” appears on the display
instead of the total playing time.
– If the system is reading the discs,
programming is not possible,
“
READING” will be displayed and
followed by " DISC X". "X" is the
current read disc number.
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
– “ SELECT A DISC” will be displayed
when programming an empty disc slot.
Reviewing the program
Reviewing of the program is possible
only when playback is stopped.
• Press
í or ë repeatedly to review
the programmed tracks.
• Press Ç to exit review mode.
Playing the program
1 Press É to start program playback.
™ “PLAY PROGRAM” will be
displayed.
™ The track number and elapsed
playing time of the current track
will appear on the display.
• If you press REPEAT during
program playback, the current track
or all programmed tracks will be
played repeatedly.
™ “TRACK” or "PROGRAM" will be
displayed.
™ The REP and PROG flags appear
on the display.
2 Press Ç to stop program playback.
Notes:
– If you press any of the DISC DIRECT
PLAY buttons, the system will play the
selected disc and the stored program
will be ignored temporarily. The PROG
display also will disappear temporarily
from the display. It will reappear when
playback of the selected disc ends.
– REPEAT DISC mode will be cancelled
when program playback begins.
Erasing the program (when
playback is stopped)
• Press
Ç.
™ “PROGRAM CLEARED” will be
displayed.
CD
Note:
– The program will be erased when the
system is disconnected from the power
supply or when the CD changer tray is
opened.
Shuffle (only on remote control)
In shuffle mode, the system plays all the
available discs and their tracks in
random order. Shuffle may be used also
when tracks are programmed.
To shuffle all the discs and tracks
1 Press SHUFFLE.
™ “SHUFFLE” will be displayed.
™ The SHUF flag and the track
selected at random appear on the
display.
• The discs and the tracks will be
played in random order until you
press
Ç.
• If you press REPEAT during
shuffling, the current track or all
available discs will be played
repeatedly.
™ “TRACK” or “ALL DISC” will be
displayed.
™ The REP and SHUF flags appear
on the display.
2 Press SHUFFLE again to resume
normal playback.
™ The SHUF flag disappears from
the display.
Note:
– REPEAT DISC mode will be cancelled
when shuffle is selected.
Repeat (only on remote control)
You can play the current track, a disc or
all available discs repeatedly.
1 Press REPEAT on the remote
control to select the various repeat
modes.
™ “TRACK”, “DISC”, “ALL DISC”
or “ OFF” will be displayed.
™ The REP flag appears on the
display.
• The selected track, selected disc or
all available discs will now be played
repeatedly until you press
Ç.
2 Press REPEAT until the " OFF"
mode is displayed to resume normal
playback.
™ The REP flag disappears from the
display.
Notes:
– REPEAT DISC mode is not available
during program play or shuffle mode.
– You can also repeat shuffling a
program.
i) “
TRACK“ or “PROGRAM" will be
displayed.
ii) The REP, PROG, and SHUF flags
appear on the display.
pg 01-28/C250/37-En 12/6/00, 2:20 PM 16