Philips 42HFL3684S-F7 - Manual (Page 10)

10
42HFL3684S 46HFL3684S 39HFL3684S
Changing picture and sound settings
You must set Home in Location. Otherwise, these settings
will not be memorized after the unit goes to standby mode.
Changing picture settings
1
Press MENU; navigate to Consumer TV setup - Picture.
2
Press Î or ï to select one of the picture settings, and
press OK to enter the setting.
3
Adjust the picture quality.
Auto Picture
You can manually set the picture controls for the Personal
setting and/or you can select one of the following Auto
Picture presets. Press Î or ï to select the desired setting,
then press OK.
Personal The customized settings you defi ned by using the
Picture menu.
Standard For normal TV viewing.
Sports Vivid picture settings for high action.
Movie Brilliant picture settings for a cinematic experience.
Game Optimized for PCs, games consoles and playstations.
4
Press MENU to exit.
Changing sound settings
1
Press MENU; navigate to Consumer TV setup - Sound.
2
Press Î or ï to highlight a sound setting and press OK
to select the setting.
3
Adjust the following items.
Auto Sound
You can manually set the sound controls for the Personal
setting and/or you can select one of the following Auto
Sound presets. Press Î or ï to select the desired setting,
then press OK.
Personal The customized settings you defi ned by using the
Sound menu.
Standard For normal TV viewing.
Movie Realistic sound settings for a cinematic experience.
Music
Emphasize high and low frequency for instrument
sound.
News Clear sound settings for human voice.
4
Press MENU to exit.
Clone TV confi guration data
Once you have completed the setup of the master TV and
tested that it receives all the required channels, follow the
TV to USB section below to extract a copy of the setup
confi guration to a USB storage device.
Then follow the USB to TV section below to copy the
setup confi guration to all additional TVs using the same
confi guration.
TV to USB
1
Connect your USB storage device to the USB port on
the side of your TV.
2
Press MENU and select TV to USB.
3
Press OK to start the copy of the confi guration data to
USB.
USB to TV
1
Connect your USB storage device to the USB port on
the side of your TV.
2
Press MENU and select USB to TV.
3
Press OK to start the copy of the confi guration data to
TV.
Note
• After this setting is completed, the TV will restart automatically.
Multi RC
Multi RC enables control of multiple TVs in a room without any
interference from each other’s remote control.
To enable Multi RC, each remote control is set to one of the
four colors - Blue, Green, Yellow or Red. Each TV in the room
is separately programmed to a remote control of one of those
colors.
In this way, each TV responds to only one RC that is set to the
same color as the TV itself. This prevents interference from each
other’s remote control when you watch multiple TVs in a room.
1
Press MENU on the setup remote control to display the
setup menu.
2
Press ОпНЖ to select Control settings.
3
Press ОпНЖ to select MultiRC.
4
Press ОпНЖ to select Select a color code.
• The TV is confi gured to respond to the RC that is set to the
same color.
5
On the guest RC, press HOME (the menu button) and
the color button (same color as above) simultaneously,
for at least 5 seconds.
• The guest RC is set to the selected color.
Note
• The Guest RC defaults to Blue, and a remote which has been
set to any color can operate any TV which has not been
confi gured to a different color yet. Therefore, if 2 TVs are being
confi gured in the same space, then each TV/RC pair MUST
be set a their own color (one pair cannot be left as default,
otherwise both RCs will operate the TV which has not been
confi gured).
LC11_PHILIPS_hospitality_S_EN_QG.indd 10 LC11_PHILIPS_hospitality_S_EN_QG.indd 10 2013/01/23 19:26:16 2013/01/23 19:26:16