Philips 2000 series LED-LCD TV 39PFL2908 39" class-po - Manual (Page 41)

41 English
Upgrading the software
USB upgrade
You can upgrade the software by using USB Memory Stick.
1
Connect your USB Memory Stick with the upgrade file to the USB
terminal on the side of your TV.
2
Use ▲▼ to select Software update, then press OK.
3
Use ▲▼ to select USB, then press OK.
4
Use ▲▼ to select the desired Update file.
5
Use ◄► to select Yes, then press OK.
6
Read the on-screen instructions and confirm that you want to
continue with the installation.
7
When the software upgrade is completed, press to set the unit
into Standby mode, then remove the USB Memory Stick.
8
Unplug the AC power cord for a few seconds from AC outlet and
plug it again.
9
Press again to Turn the unit On.
• The TV starts up with the new software.
For further assistance, please contact Call Center.
Network update
You can update the software by connecting the unit to the Internet.
1
Use ▲▼ to select Software update, then press OK.
2
Use ▲▼ to select Network, then press OK.
3
Use ◄► to select Yes, then press OK.
• This unit will then start checking for the latest firmware version.
4
Confirmation message will appear.
Use ◄► to select Yes, then press OK.
• The unit will start downloading the latest firmware version.
• The unit will start updating the firmware version.
• It may take a while to complete the updating.
5
When the software update is complete, press to make sure the
unit goes to Standby mode.
6
Unplug the AC power cord for a few seconds from AC outlet and
plug it again.
7
Press again to Turn the unit On.
• The TV starts up with the new software.
For further assistance, please contact Call Center.
Recovery update
If the unit turns off during the software upgrade, an error message will
be displayed when you turn it on next time. In this case, please follow
the procedure below to start the software upgrade again. The unit will
not work correctly unless the software upgrade is completed.
1
Follow steps 1 to 2 in Downloading the software ➟ p.40
2
Click the software for recovery update to be downloaded.
• Decompress the ZIP-file.
3
Copy the recovery update file to the root directory of the USB
Memory Stick
4
Connect the USB Memory Stick with the recovery update file to
the USB terminal on the side of your TV, then press OK.
5
When the software update is complete, remove the USB Memory
Stick.
6
Unplug the AC power cord for a few seconds from AC outlet and
plug it again.
• The TV starts up with the new software.
For further assistance, please contact Call Center.
Automatically check for latest software
This function lets you know if the latest software is available while the
unit is connected to the Internet.
1
Use ▲▼ to select Automatically check for latest software, then
press OK.
2
Use ▲▼ to select the desired option, then press OK.
Netflix deactivation
Displays the deactivation setting for Netflix.
1
Use ▲▼ to select Netflix deactivation, then press OK.
2
Use ▲▼ to select the desired option, then press OK.
Software update is in progress. Please wait.
Do not remove the USB storage device or turn the TV off while
upgrade is in progress.
Update your TV with new software:
Note
• In order to update software via the Internet, you must connect the unit to the Internet
and set up necessary settings. Network settings assistant ➟ p.37 Network ➟ p.37
• Please do not unplug the AC power cord or Ethernet cable while executing the
Network update.
• All settings will remain the same even if you update the software version.
• The version of Net service will also be updated if newer version of Net service is
available when updating the firmware.
Off Disable automatically check for latest software.
On
A message will appear if there is the latest software on the
network server.
Off Deactivate the connection to Netflix.
On Activate the connection to Netflix.