Liebherr TP 1760 Premium - Manual (Page 10)

6.1.2 Defrosting freezer compartment*
A layer of frost and ice forms in the freezer compartment after
the appliance has been in use for a lengthy period of time. This
is quite normal. The layer of frost and ice forms more quickly if
the door is opened frequently or if the food is warm when
placed inside. However, a thick layer of ice will increase the
appliance‘s energy consumption. You should therefore defrost
the appliance regularly.
CAUTION
Risk of injury and damage as a result of hot steam!
u Do not use electric heaters or steam cleaners, naked flames
or defrosting sprays for defrosting.
u Do not remove ice using sharp instruments.
u Switch on SuperFrost one day before defrosting.
u Switch off the appliance.
w The temperature display goes out.
w If the temperature display does not go out, the child-proofing
function (see 5.2) is active.
u Pull out the plug.
u Wrap the frozen food in newspaper or blankets and store in
a cool place.
u Leave the compartment and appliance door open during
defrosting.
u Remove detached pieces of ice.
u If necessary, pick up defrost water several times, using a
sponge or cloth.
u Clean the compartment (see 6.2) .
6.2 Cleaning the appliance
WARNING
Risk of injury and damage as a result of hot steam!
Hot steam can lead to burns and can damage the surfaces.
u Do not use any steam cleaners!
NOTICE
Incorrect cleaning damages the appliance!
u Do not use cleaning agents in concentrated form.
u Do not use any scouring or abrasive sponges or steel wool.
u Please do not use any aggressive, scouring, sand-,
chloride-, chemical- or acid-based cleaning agents.
u Do not use chemical solvents.
u Do not damage or remove the type plate on the inside of the
appliance. It is important for the customer service.
u Do not pull off, bend or damage cables or other compo-
nents.
u Do not allow any cleaning water to enter the drain channel,
ventilation grille or electrical parts.
u Please use soft cleaning cloths and a universal pH-neutral
cleaning agent.
u Please use cleaning and care products suitable for contact
with foodstuffs in the appliance interior.
u Empty appliance.
u Pull out the power plug.
u Clean the vent grille regularly.
w Dust deposits increase energy consumption.
u Clean plastic outer and inner surfaces with lukewarm
water and a little washing-up liquid.
u Only use a soft clean cloth to wipe side walls with a paint
finish. In the case of heavy soiling, use lukewarm water with
neutral cleaning agent.
u Clean drain hole: Remove deposits
with a narrow instrument, e.g. a
cotton bud.
u Clean items of equipment by hand with lukewarm water
and a little washing-up liquid.
After cleaning:
u Wipe dry the appliance and items of equipment.
u Connect the appliance and switch it on again.
u Switch on SuperFrost (see 5.4.4) .*
u Put the food back inside.
6.3 Replacing the interior illumination
with LED lamp
In the device, an LED lamp is used as standard illumination for
the interior space.
When an incandescent bulb is used:
q Use an incandescent lamp with max. 15 W and E14 socket.
q Power supply (AC) and voltage at the operating point must
comply with the details on the rating plate (see Appliance at
a glance).
When a LED is used:
q Use only the original LED lamp from the manufacturer. The
lamp can be obtained through customer service or a
specialist dealer (see 6.4) .
WARNING
Risk of injury from LED light!
The light intensity of the LED lighting corresponds to laser
class 1/1M.
If the cover is removed:
u Do not look directly into the light at close quarters through
optical lenses. Doing so may damage your eyes.
WARNING
Fire hazard from the LED light!
If different LED lights are used, there is a danger of overheating
or fire.
u Use the manufacturer's original LED light.
u Switch off the appliance.
u Pull out the mains plug or switch off/unscrew the fuse.
u Take hold of the lamp cover at
the top and bottom Fig. 13 (1) .
u Disengage the lamp cover at
the back and detach it
Fig. 13 (2) .
u Replace the lamp Fig. 13 (3) .
u Clip the back end of the cover
in and clip the sides into place.
Fig. 13
6.4 Customer service
First check whether you can correct the fault yourself by refer-
ence to the list (see Malfunction). If this is not the case, please
contact the customer service whose address is given in the
enclosed customer service list.
Maintenance
10 * Depending on model and options