Buhler Commercial Snowblower - Manual (Page 31)

Commercial Snowblower
30
SPECIFICATIONS
MODEL
B6022HSB-1
B6022HSB-2
B6022HSB-3
B7422HSB-1
B7422HSB-2
B7422HSB-3
B7422HSB-4
B7424HSB-3
B7424HSB-4 B8424HSB-2
B8424HSB-3 B84SB
(PTO Drive)
Cutting Width 60" 74" 74" 84" 84"
Cutting Height 28” 30” 30” 30” 30”
Fan Housing
Replaceable
UHMW Liner
Replaceable
UHMW Liner
Replaceable
UHMW Liner
Replaceable
UHMW Liner
Replaceable
UHMW Liner
Fan 4-Blade 4-Blade 4-Blade 4-Blade 4-Blade
Fan Diameter 21.5” 21.5” 23.5” 23.5” 23.5”
Fan Depth 7.5” 7.5” 7.5” 7.5” 7.5”
Auger Diameter 20” 20” 20” 20” 20”
Auger Center
Diameter
3”od x .150 wall 3”od x .150 wall 3”od x .150 wall 3”od x .150 wall 3”od x .150 wall
Auger
Thickness
3/8” 3/8” " 3/8” 3/8” 3/8”
Drive Fan Hyd w/#80 Chain Hyd w/#80 Chain Hyd w/#80 Chain Hyd w/#80 Chain PTO Gearbox
Drive Auger Hyd w/#60H Chain Hyd w/#60H Chain Hyd w/#60H Chain Hyd w/#60H Chain #60H Chain
Body Housing 10ga 10ga 10ga 7ga 7ga
Hitch Type Skid Steer-fixed Skid Steer-fixed Skid Steer-fixed Skid Steer-fixed Cat. 3 –3 pt.
Hitch
Adjustment No
No No No 3 position
Chute Rotator Hydraulic-230 Hydraulic-230 Hydraulic-230 Hydraulic-230 Hydraulic-230
Chute Deflector Hyd. Hyd. Hyd. Hyd. Hyd.
Cutting Edge
½” x 4” Beveled
replaceable
½” x 4” Beveled
replaceable
½” x 4” Beveled
replaceable
½” x 4” Beveled
replaceable
½” x 4” Beveled
replaceable
Skid Shoes
Cup Type –
adjustable
Cup Type –
adjustable
Cup Type –
adjustable
Cup Type –
adjustable
Cup Type –
adjustable
Truckloading
Spout Opt.
Opt. Opt. Opt. Opt.
System
Controls &
Drive Hyd. Load
Sensing Block flow
adjustable
Hyd. Load
Sensing Block flow
adjustable
Hyd. Load
Sensing Block flow
adjustable
Hyd. Load
Sensing Block flow
adjustable PTO w/shear pin
Hyd.
Requirements 13-26 gpm
2000 psi Min.
13-32 gpm
2000 psi Min.
20-32 gpm
2000 psi Min.
20-32 gpm
2000 psi Min.
10 gpm
1000 psi Min.
Approx. Weight 1070 lbs. 1178 lbs. 1193 lbs. 1209 lbs 1307 lbs.
Hydraulic Snowblower Fan RPM to GPM Rating
Series I
13 – 17 gpm 2000 psi min. (6.2 cu.in./rev)
Series II 16 – 22 gpm 2000 psi min. (8 cu.in./rev)
Series III 20 – 26 gpm 2000 psi min. (9.6 cu.in./rev)
Series IV 24 – 32 gpm 2000 psi min (11.9 cu.in./rev)
gpm x psi = hp
1714