Barco R9000977 - Manual (Page 47)

7.
5975628J BARCOGRAPHICS 1209S 010797 41
7.14 G2
2 3 2 3 2 3 2 3
I;01*+,()-.G"#$
G2 ADJUST
ENTER !ABCD"#$
G2 KL#/*¸(o)D/*+23/ ±,-â
.g02ef"#$
!"# !"# !"# !"#
ENTER !#JABCD "#2ouqr;%
&st/Ý0;}* EXIT !%&'(V
VWXdyG$ G2 KL;12S34*{|5
WX8ãG"#$
7.15
4 # 5 6 7 4 # 5 6 7 4 # 5 6 7 4 # 5 6 7
I;01*+,()-.G"#$
)ï
GAMMA CORRECTIONS ð
ENTER !"#$
I;cA*hijk;KLEÁ"Hš23/
;)žŸ2"#$
$ $ $ $%& %& %& %& '( '( '( '( )*+) )*+) )*+) )*+),,,,- - - - ./0 ./0 ./0 ./0 123 123 123 1234 4 4 45 5 5 56 6 6 6
789:#; 789:#; 789:#; 789:#;<<<<
= = = = >?@
A >?@
A >?@
A >?@
A
BC#D !"# BC#D !"# BC#D !"# BC#D !"#<<<<
ENTER !#J65;7˜2Å_"#2opqr;
%&st/Ý0* EXIT !%&'(V
VWXd–EFG$65;7˜UG;1G
34*{|5WX8;8 C ã9G"#$
7.16 CRT
" # " # " # " # $ # $ # $ # $ # $ 8 $ 8 $ 8 $ 8
CRT %эhˆо*»:+k;V
'„:®2{rG/á;;ÈÅz7)#$ 1 Uݸ
;»:+kP:®2{rG/<=*<,
e$2=>5 5 ?Ð ON 5 ?Ð OFF >Z[;»:®
UG 5 @РAC"#$\; 5 @Р)*B 2 ;»:®2´
P<,e$2=>"#$e$* CRT ;CDQD
E; ±FGˆ"#$ CRT %
эhˆохц/* EXIT !"#$
CRT RUN IN CYCLE
ENTER !Hô"#$
»:+k)KL V'„:®2´P)Q/<=
CRT %* ENTER !#JHô"#$
:®2{rGSG<=hijk* CRT
эhˆоИЕ#/IJ2)QÁKL'(ID"
#$
I;á
CRT %ÈÅ G<=*Z[
»:+k;V'„:®A CRT
эhˆоJHф"#$
SERVICE MODE
Select with or
then
to return
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
SERVICE MODE
Select with or
then
to return
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
SERVICE MODE
Select with or
then
to return
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
CRT RUN IN CYCLE
to continue
to cancel
797
A flashing white pattern
will be generated until
is pressed.
The projector only uses
memory blocks adjusted
on an internal # pattern;
if no such block is
available, the projector
can't run the procedure
and leaves the adjustment
mode.
SAFETY
NOTICE
RISK OF ELECTRICAL SHOCK
G2 ADJUSTMENT SHOULD BE
PERFORMED BY BARCO
PERSONNEL, OR BARCO
AUTHORIZED DEALERS.
IF QUALIFIED, PRESS
TO CONTINUE, OR
IF NOT, TO RETURN.
WARNING
RISK OF INCORRECT
ADJUSTMENT OF THE PROJECTOR
TO CONTINUE, OR
IF NOT, TO RETURN.
THE GAMMA CORRETIONS ARE
FACTORY ADJUSTED USING AN
ACTAS COLOUR ANALYSER!
THEREFORE, ONLY QUALIFIED
INSTALLATION OR SERVICE
PERSONNEL SHOULD PERFORM
THESE ADJUSTMENTS!