Warning – Whirlpool WRF991BOOM User Manual
Page 20
20
1. Press MEASURED FILL to turn on the feature. When the
feature is on, the Measured Fill screen appears on the display.
NOTES:
■
The dispenser will automatically turn off Measured Fill
after 1 minute of inactivity. When Measured Fill is turned
off, any changes you have made will be lost and all
defaults will be restored.
■
Press ICE/WATER “Back,” to manually turn off the
Measured Fill feature.
2. Press LIGHT, under Units, to toggle among ounce, cup and
liter. The default unit is ounce.
Default, minimum, and maximum volumes are listed below.
3. Press LOCK or OPTIONS to adjust the water volume as
desired. The LOCK control increases the volume, and the
OPTIONS control lowers the volume.
NOTES:
■
When increasing or decreasing the dispense volumes, if
an adjustment button (-/+) is held for approximately
10 seconds or longer the control may stop responding.
Release the button for approximately 2 seconds and then
continue making the adjustment.
■
Most coffee cups (commonly 4 to 6 oz [118 to 177 mL] per
cup) are not the same size as a measuring cup (8 oz
[237 mL]). You may need to adjust the volume to avoid
unintentionally overfilling coffee cups.
4. Dispense water.
NOTE: While dispensing water, the digital display will count
down how much water remains to be dispensed, according to
the volume you selected. The flow of water will automatically
stop once the desired volume has been dispensed.
■
Press a sturdy glass against the dispenser paddle.
OR
■
Place the glass below the water dispenser and press
MEASURED FILL, under Dispense, for hands-free
dispensing.
5. To stop dispensing before the selected volume has been
dispensed, remove the glass from the dispenser paddle OR
press MEASURED FILL a second time.
NOTE: If you stop dispensing before the desired volume has
been dispensed, the digital display will continue to show how
much water remains to be dispensed. The display will turn off
after 1 minute of inactivity.
■
To select a new volume or start dispensing the same
volume again, you must first finish dispensing the selected
volume, or turn off the Measured Fill feature (either by
waiting 1 minute so it will automatically turn off or by
pressing ICE/WATER “Back” to manually turn it off) and
then turn it back on.
The Ice Dispenser
IMPORTANT:
■
If the ice cubes are hollow or have an irregular shape, it could
be because of low water pressure. See “Water Supply
Requirements.”
■
Ice travels from the ice storage bin through the dispenser
chute to the dispenser. To turn off the ice maker, see “Ice
Maker and Storage Bin.”
To Clean the Ice Dispenser Chute:
Humidity causes ice to naturally clump together. Ice particles can
build up until the ice dispenser chute becomes blocked.
If ice is not dispensed regularly, it may be necessary to empty the
ice storage bin and clean the ice delivery chute, the ice storage
bin and the area beneath the storage bin every 2 weeks.
■
Remove the ice clogging the storage bin and delivery chute,
using a plastic utensil if necessary.
■
Clean the ice delivery chute and the bottom of the ice storage
bin using a warm, damp cloth, then dry thoroughly.
To Dispense Ice:
1. Select the desired type of ice. To switch between cubed ice
and crushed ice, press ICE/WATER.
2. Press a sturdy glass against the dispenser paddle. Hold the
glass close to the dispenser opening so ice does not fall
outside of the glass.
IMPORTANT: You do not need to apply a lot of pressure to the
paddle to activate the ice dispenser. Pressing hard will not
make the ice dispense faster or in greater quantities.
3. Remove the glass to stop dispensing.
NOTE: Ice may continue to dispense for several seconds after
removing the glass from the dispenser paddle. The dispenser may
continue to make noise for a few seconds after dispensing.
The Dispenser Light
When you use the dispenser, the light will automatically turn on.
To turn on the light when you are not dispensing:
Press LIGHT to toggle through the following choices in a
continuous loop:
■
OFF (default) - The dispenser light is off
■
ON - The dispenser light remains on at 100% brightness
■
DIM - The dispenser light remains on at 50% brightness
The dispenser lights are LEDs that cannot be changed. If it
appears that your dispenser lights are not working, see
“Troubleshooting” for more information.
Units
Default
Minimum
Maximum
Ounces
8
1
128
Cups
1
¹/₄
16
Liters
0.25
0.05
4.00
ON
DIM
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.
WARNING