Whirlpool WCC31430AR - Manual

PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
WCC31430A
Before You Make the Electrical Connection:
To properly install your cooktop, you must determine the type of electrical
connection you will be using and follow the instructions provided for it here.
● A 4-wire or 3-wire, single phase, 240 volt, 60 Hz., AC only electrical supply is
required on a separate, 40-amp circuit, fused on both sides of the line. The
model/serial number rating plate is located on the metal cabinet underneath
the cooktop. See the following illustration.
● Cooktops with 3-wire cable coming from the cooktop are rated 240 volt and
do not have a neutral (white) wire.
● The cooktop should be connected directly to the junction box through
flexible, armored or nonmetallic sheathed, copper cable. The flexible, armored
cable extending from the fuse box or circuit breaker box should be connected
directly to the junction box.
● Locate the junction box to allow as much slack as possible between the
junction box and the cooktop so that the cooktop can be moved if servicing
becomes necessary in the future.
● Do not cut the conduit. Use the length of conduit provided.
● A UL listed or CSA approved conduit connector must be provided at each end
of the power supply cable (at the cooktop and at the junction box). A listed
conduit connector is already provided at the cooktop.
● If the house has aluminum wiring, follow the procedure below:
1. Connect a section of solid copper wire to the pigtail leads.
2. Connect the aluminum wiring to the added section of copper wire using
special connectors and/or tools designed and UL listed for joining copper
to aluminum.
Follow the electrical connector manufacturer's recommended
procedure. Aluminum/copper connection must conform with local
codes and industry accepted wiring practices.
Electric Built-in Cooktop
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice. Ref. W10458811A
9/13/12
C
A
B
A. 21" (53.3 cm)
B. 30" (76.2 cm)
36" (91.4 cm)
C. 3¼" (8.3 cm)
A. 30" (76.2 cm)
B. Combustible area above countertop (shown by dashed box above)
C. 30" (76.2 cm) minimum clearance between top of cooktop platform
and bottom of uncovered wood or metal cabinet.
24" (61 cm) minimum clearance if bottom of wood or metal cabinet
is covered by not less than " [0.6 cm] flame retardant millboard
covered with not less than No. 28 MSG sheet steel,
0.015" [0.04 cm] stainless steel or 0.024" [0.06 cm] aluminum or
0.020" [0.05 cm] copper)
D. 13" (33 cm) recommended upper cabinet depth
E. 3" (7.6 cm)
F. 19 " (50.3 cm) recommended cutout on all models
G. 18" (45.7 cm) minimum clearance from upper cabinet to
countertop within minimum horizontal clearances to cooktop
H. Junction box or outlet; 12" (30.5 cm) minimum from bottom of
countertop
I. Junction box or outlet; 10" (25.4 cm) from right side of cabinet
J. 28
⁵⁄₁₆
" (71.9 cm) recommended cut-out on 30" (76.2 cm) Whirlpool
models
K. 1" (2.5 cm) minimum distance to nearest left and right side
combustible surface above cooktop
L. 1" (2.5 cm) minimum clearance between back wall and countertop
¹⁄₄
¹³⁄₁₆
A. Model/serial number plate
A
CABINET OPENING DIMENSIONS
D
A
E
I
J K
G
H
L
C
F
B
IMPORTANT: If installing a range hood or microwave hood
combination above the cooktop, follow the range hood or microwave
hood combination installation instructions for dimensional clearances
above the cooktop surface.
NOTES: After you make the countertop cutout, some installations
may require notching down the base cabinet side walls to clear the
cooktop base. To avoid this modification, use a base cabinet with
sidewalls wider than the cutout.
If cabinet has a drawer, a 3 ¹⁄₄" (9.6 cm) depth clearance from the top of
the countertop to the top of the drawer (or other obstruction) in base
cabinet is required.