Pioneer CDJ-100S - Manual (Page 11)

11
En
Using Digital Jog Break
During playback, press one of the DIGITAL JOG BREAK
buttons (JET, ZIP, WAH); in the display, the indicator cor-
responding to the selected effect will flash, and the ef-
fect will be applied to the sound in proportion to the
amount the jog dial is rotated.
÷ When the jog dial is released, the sound will gradu-
ally return to the original source sound alone.
7 What is JET?
JET means to change the delay time by rotating the jog
dial, thus mixing a short delay with the playback sound.
Conventional DJ technique has been to use 2 players,
starting the same track simultaneously on both players,
then introducing a slight delay on one of the players,
mixing the two sounds so as to produce the effect of a
"jet engine." This function allows you to produce this
sound effect easily using a single player.
7 What is ZIP?
The pitch of the playback sound is changed in accord-
ance with the rotation of the jog dial, allowing you to
radically change the tonal pitch of the playback sound.
When the dial is held rotated in the decreasing direc-
tion, a sound can be created virtually indistinguishable
from stopping the rotation of an analog record.
7 What is WAH?
When the jog dial is rotated, a filter changing the cutoff
frequency is applied to the playback sound, in accord-
ance with the amount the dial is rotated. This allows the
DJ to extract and play back desired parts from the play-
back sound.
Using the HOLD function
Press the HOLD button while the DIGITAL JOG BREAK
function is in effect; in the display, the indicator corre-
sponding to the selected effect will switch from flashing
to steadily lighted, and the amount of effect currently
being applied to the sound will remain steady, even if
the jog dial is released.
÷ When the HOLD function is in effect, the time display
will periodically show the HOLD indicator as noted
below.
JET + HOLD: J-HOLD
ZIP + HOLD: Z-HOLD
WAH + HOLD: W-HOLD
SPECIAL DISC JOCKEY TECHNIQUES
Jog Dial Functions
Playback
During playback, rotate the jog dial slowly
÷ The beat (tempo) changes in proportion to the amount
the dial is rotated, either increasing (FWD+) or decreas-
ing (REV–).
÷ When dial rotation is stopped, the beat (tempo) re-
turns to its original speed.
Standby (Frame Search)
With the unit in standby mode, rotate the jog dial slowly.
÷ Frame search will be performed in 1-frame increments.
÷ If the dial is rotated at a steady rate in the FWD+ di-
rection, playback sound will be audible (normal
speed).
During Cue Standby, Press Search Button then
Rotate Dial (Cue Point Search).
With the unit in the cue standby mode, if one of the
SEARCH buttons (
1, ¡ ) is pressed, the unit will en-
ter the audible standby mode; if the jog dial is then ro-
tates, various cue points can be searched. Following
movement, press the CUE button to set the new cue
point.
Rotate the jog dial while holding the TRACK
SEARCH button depressed. (Super-Fast Track
Search)
While holding the TRACK SEARCH button depressed,
rotate the jog dial in the direction in which you wish to
perform track search; accelerated high-speed track search
will begin in accordance with the direction and mount of
rotation.
During playback, rotate the jog dial while holding
the SEARCH button depressed. (Super-Fast Search)
Hold down the button while turning the Jog dial in the
direction you wish to search to enter fast forward or fast
reverse mode.
ADVANCED OPERATIONS
Master Tempo
1. During playback, press the MASTER TEMPO
button.
÷ The MT indicator will appear in the display.
2. Move the TEMPO slider to change the playing
speed.
÷ Even when the music's speed changes, the music
pitch does not change.
Jog dial