Pioneer XW-PSS01-L - Manual

Power Line Network Speaker
XW-PSS01-L
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
D3-4-2-3-2_A_En
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance. The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons. CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
IMPORTANT
D3-4-2-1-1_En-A
Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified
service personnel.
D3-4-2-1-2-2_B_En
IMPORTANT: THE MOULDED PLUG
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the
fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug
must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.
If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of
safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Blue : Neutral Brown : Live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows ;
The wire which is coloured BLUE must be connected to the terminal which is marked with the
letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter L or coloured RED.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
[U.K. model only]
WARNING
This equipment is not waterproof. To prevent a fire
or shock hazard, do not place any container filed
with liquid near this equipment (such as a vase or
flower pot) or expose it to dripping, splashing, rain
or moisture.
D3-4-2-1-3_A_En
WARNING
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230V
or 120V) written on the rear panel.
D3-4-2-1-4_A_En
Before plugging in for the first time, read the following
section carefully.
WARNING
To prevent a fire hazard, do not place any naked
flame sources (such as a lighted candle) on the
equipment.
D3-4-2-1-7a_A_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat
radiation (at least 60 cm at top, 10 cm at rear, and
30 cm at each side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the
product, and to protect it from overheating. To
prevent fire hazard, the openings should never be
blocked or covered with items (such as newspapers,
table-cloths, curtains) or by operating the
equipment on thick carpet or a bed.
D3-4-2-1-7b_A_En
Operating Environment
Operating environment temperature and humidity:
+5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c_A_En
This product complies with the Low Voltage Directive
(73/23/EEC, amended by 93/68/EEC), EMC Directives
(89/336/EEC, amended by 92/31/EEC and
93/68/EEC).
D3-4-2-1-9a_En
[European model only]
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left
unused for a long period of time (for example, when
on vacation).
D3-4-2-2-1a_A_En
CAUTION
The Standby/On switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from
the AC outlet to shut down all power. Therefore,
make sure the unit has been installed so that the
power cord can be easily unplugged from the AC
outlet in case of an accident. To avoid fire hazard,
the power cord should also be unplugged from the
AC outlet when left unused for a long period of time
(for example, when on vacation).
D3-4-2-2-2a_A_En
WARNING
Do not use or store batteries in direct sunlight or
other excessively hot place, such as inside a car or
near a heater. This can cause batteries to leak,
overheat, explode or catch fire. It can also reduce the
life or performance of batteries.
D3-4-2-3-3_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which
requires repair will be charged for even during the
warranty period.
K041_En
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used
electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to
designated collection facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential
negative effects on the environment and human health.
K058_En
[European model only]
Discover the benefits of registering your product online at www.pioneer.co.uk
(www.pioneer-eur.com).
[European model only]
Before you start
Caution: installation
• Do not place the speaker on an unstable surface. It could present a hazard if it falls, as well as
damaging the equipment.
• Do not put a TV or other AV equipment on top of this speaker. It could present a hazard if it falls,
as well as damaging the equipment.
Caution: in use
• Do not use the speaker to output distorted sound for long periods of times. This can result in a
fire hazard.
• Do not sit or stand on the speaker, or let children play on the speaker.
• Do not put large or heavy objects on top of the speaker.
• Do not install your speakers overhead on the ceiling or wall.
• Do not attach these speakers to the wall or ceiling. They may fall off and cause injury.
• Keep the speaker away from water and moisture. Do not place the speaker in the bathroom or
other places where it will be exposed to extreme moisture.
Usage precautions
• Conditions considered unpleasant by humans are detrimental to speakers as well. Providing a
comfortable environment for the speakers will assist them in demonstrating their best
performance. Please maintain the usage environment as follows:
Temperature: 15 °C to 25 °C
Relative Humidity: 35 % to 65 % (winter)
40 % to 70 % (summer)
• In areas of high humidity, use a dehumidifier, and in areas of excessive dryness, use a humidifier
to adjust the room’s humidity level.
• Avoid exposure to direct sunlight, and do not install in areas nearby heating appliances.
• When using room air-conditioners or stoves to rapidly cool or heat room spaces, take precautions
to avoid excessive dehumidification.
• Avoid locations near windows or in other locations where speakers may be exposed to the
influence of outdoor air, since condensation may result.
Cleaning the speaker cabinet
With normal use, wiping with a dry cloth should be sufficient to keep the cabinet clean. If necessary,
clean with a cloth dipped in a neutral cleanser diluted five or six times with water, and wrung out well.
Do not use furniture wax or cleansers.
Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit since these will
corrode the surfaces.
Magnetic shielding
This speaker system is magnetically shielded. However, depending on the installation location, color
distortion may occur if the speaker system is installed extremely close to the screen of a television set.
If this happens, turn off the television, then turn it on again after 15 min to 30 min. If the problem
persists, place the speaker system away from the television set.
About this speaker
• Using this system, you can listen to sound sources from the Power Line Sound Station simply by
plugging the power cord into an AC outlet in your home. For example, you could place the Power
Line Sound Station in the living room of your house, then set up separate speakers in your
kitchen, hallway and bedroom to listen to music wherever you want in your home.
• Thanks to the remote sensor on the optional XW-PSS01-L speaker supplied with this system, you
can control the Power Line Sound Station, even while listening to music in another room.
Installation
Speaker systems are delicately influenced by the conditions of the listening room where they are used.
As a result, you should take care to provide optimum conditions for your listening environment.
Note: Pioneer refuses any responsibility for damage or accidents resulting from improper
installation.
• Each speaker weighs 2.8 kg. Select a stable surface for installation.
Operating range of remote control unit
The Power Line Sound Station can be controlled by the remote via the speaker’s remote sensor. The
operating range of the remote is shown below.
The remote control may not work properly if:
• There are obstacles between the remote control and the speaker's remote sensor.
• Direct sunlight or fluorescent light is shining onto the remote sensor.
• The speaker is located near a device that is emitting infrared rays.
• The speaker is operated simultaneously with another infrared remote control unit.
Specifications
Power consumption .................................................................................................................................. 24 W
Power output ................................................................................................................. 25 W/ch (1 kHz, 10 %)
Power Requirements
European/UK models ................................................................................ AC 230 V to 240 V, 50 Hz/60 Hz
Australia/New Zealand models ............................................................................... AC 240 V, 50 Hz/60 Hz
Taiwan model ....................................................................................................................... AC 110 V, 60 Hz
All other models ......................................................................................... AC 110 V to 240 V, 50 Hz/60 Hz
Enclosure ....................................................................... Closed-box bookshelf type (magnetically shielded)
Configuration
Full-range ...................................................................................................................... 7.7 cm cone type x 2
Nominal impedance .................................................................................................................................... 6
Ω
Exterior dimensions ...................................................................... 452 (W) mm x 162 (H) mm x 112 (D) mm
Weight ....................................................................................................................................................... 2.8 kg
Supplied accessories
Remote Control
Lithium battery (CR2025) x 1
Power plug adaptor (multi-voltage model only) x 1
Operating Instructions
Controls and Displays
Plugging in the speaker
Plug the AC power cord into a convenient AC power outlet.
Please refer to Power Line Sound System connections in the XW-PSS01 operating instructions for
recommended connections.
Setting the speaker ID
When the speaker is used as an optional speaker with the Power Line Sound Station, it is necessary to
assign it an ID in order for the system to work properly. Plug the Power Line Sound Station and the
Speaker into two AC power sockets. The power sockets should be as close as possible to one another,
ideally on the same outlet.
1 Switch on the Power Line Sound Station.
2 Press and hold then press DUAL on the Power Line Sound Station.
The display shows Id SEt.
3 Switch on the speaker.
4 Press and hold then press CH Select on this speaker.
The speaker ID setting is confirmed when Id has finished flashing.
5 Press and hold then press DUAL on the Power Line Sound Station.
The ID setting is complete after finishes flashing (about ten seconds).
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S002_En
Speaker controls
CH Select
CH Select
Standby / On
Inpu t Sel . S ound Mu te
1 2 3 4 5
1 Standby/On
Switches on or into standby (the standby
indicators on the speaker light red when
standby).
• Both the speaker and Power Line Sound
Station switch on/into standby.
2 Channel Selector
Select channel A or B on the Power Line
Sound Station for playback.
3 Volume controls
Adjusts the volume on the speaker.
4 Display
Displays the input source in an
abbreviated form and volume.
5 Remote sensor
To control the system, point the
remote at this speaker (not at the
selector unit).
• Specifications and design subject to possible modification without
notice, due to improvements.
For repair, it is necessary to bring the main system (Power Line Sound System), as well as this
speaker (XW-PSS01-L) to your authorized Pioneer Service Center.
[European model only]
Thank you for buying this Pioneer product. Please read through these operating instructions so you
will know how to operate your model properly. After you have finished reading the instructions, put
them away in a safe place for future reference.
Please note that this speaker is a component of complete speaker system (including the XW-PSS01
Power Line Sound Station), and will not function as a stand-alone component.
The above AC plug/outlet is for illustration purposes
only. The power connections depend on region. Please refer to the troubleshooting guide in the XW-PSS01 operating instructions if you experience
problems with the operation of this unit.
<06H00001> Printed in
When using this product follow the instructions
written on the underside of the unit, which
concern rated voltage, etc.
D3-4-2-2-4_En
Important
Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following
precautions:
• Never use new and old batteries together.
• Insert the plus and minus sides of the batteries properly according to the marks in the battery
case.
• Batteries with the same shape may have different voltages. Do not use different batteries
together.
• When disposing of used batteries, please comply with governmental regulations or environmental
public instruction's rules that apply in your country or area.