Pioneer VSX-422-S - Manual (Page 28)

6 6
28
Chapter
Home Menu
Using the Home Menu
The following section shows you how to make detailed
settings to specify how you’re using the receiver, and also
explains how to fine-tune individual speaker system settings
to your liking.
Important
• The OSD will not appear if you have connected using the
HDMI output to your TV. Use composite connections for
Home Menu.
• If headphones are connected to the receiver, disconnect
them.
1
Switch on the receiver and your TV.
Press
 RECEIVER to switch on.
2
Switch the TV input to the input that connects this
receiver to the TV through the corresponding
composite cable.
3
Press , then press HOME MENU .
The Home Menu appears on your TV. Use /// and
ENTER on the remote control to navigate through the
screens and select menu items. Press RETURN to exit
the current menu.
• Press HOME MENU at any time to exit the Home
Menu.
4
Select the setting you want to adjust.
• Auto MCACC – This is a quick and effective automatic
surround setup (see Automatically setting up for surround
sound (MCACC) on page 17 ).
• Manual SP Setup
- Speaker Setting – Specify the size and number of
speakers you’ve connected (see below).
- X.Over – Specify which frequencies will be sent to the
subwoofer ( page 29 ).
- Channel Level – Adjust the overall balance of your
speaker system ( page 29 ).
- Speaker Distance – Specify the distance of your
speakers from the listening position ( page 30 ).
• Input Assign – Specify what you’ve connected to the
ANALOG IN1 audio input (see The Input Assign menu on
page 30 ).
• Pre Out Setting – Specify how to use the PRE OUT SURR
BACK/FRONT HEIGHT outputs (see The Pre Out Setting on
page 31 ).
• Auto Power Down – Sets to automatically turn off the
power when the receiver has not operated for several hours
(see The Auto Power Down menu on page 31 ).
• FL Demo Mode – Sets the demo display on the front panel
display (see The FL Demo Mode menu on page 31 ).
• HDMI Setup – Set the audio return channel function (see
The HDMI Setup menu on page 31 ).
Manual speaker setup
This receiver allows you to make detailed settings to optimize
the surround sound performance. You only need to make
these settings once (unless you change the placement of your
current speaker system or add new speakers).
These settings are designed to fine-tune your system, but if
you’re satisfied with the settings made in Automatically
setting up for surround sound (MCACC) on page 17 , it isn’t
necessary to make all of these settings.
Important
• Depending on the Pre Out Setting, there will be
differences in the speaker items that can be adjusted. The
OSD display for these operating instructions is an example
of when the Pre Out Setting is set to Surr. Back.
Speaker Setting
Use this setting to specify your speaker configuration (size,
number of speakers). It is a good idea to make sure that the
settings made in Automatically setting up for surround sound
(MCACC) on page 17 are correct.
1
Select ‘Manual SP Setup’ from the Home Menu.
2
Select ‘Speaker Setting’ from the Manual SP Setup
menu.
3
Choose the set of speakers that you want to set then
select a speaker size.
Use / to select the size (and number) of each of the
following speakers:
• Front – Select LARGE if your front speakers reproduce bass
frequencies effectively, or if you didn’t connect a
subwoofer. Select SMALL to send the bass frequencies to
the subwoofer.
RECEIVER
H o m e M e nu
1 . Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
5.Auto Power Down
6.FL Demo Mode
7.HDMI Setup
R e t u r n
2.Manual SP Setup
Return
a.Speaker Setting
b.X.Over
c.Channel Level
d.Speaker Distance
2a.Speaker Setting
Front
Center
Surr
Surr. Back
Subwoofer:
Return
[ SMALL ]
[ SMALL ]
[ NO ]
YES
SMALL