Pioneer HTP-073 - Manual (Page 27)

05 05 Listening to your system
27
En
Note
• During ECO mode, the brightness switches between 2
levels. If the dimmest level is selected, DIMMER will be
shown on the display. (Mode other than ECO: 4 levels,
ECO mode: 2 levels)
• ECO MODE will switch OFF automatically when switched
to other listening modes (Advanced surround mode and
Auto surround mode).
Using Stream Direct
Use the Stream Direct modes when you want to hear the
truest possible reproduction of a source. All unnecessary
signal processing is bypassed.
Using the Sound Retriever
When audio data is removed during the compression
process, sound quality often suffers from an uneven sound
image. The Sound Retriever feature employs new DSP
technology that helps bring CD quality sound back to
compressed 2-channel audio by restoring sound pressure
and smoothing jagged artifacts left over after compression.
1 Press S.RETRIEVER to switch the S.RTV (Sound Retriever)
ON or OFF.
Note
• The Sound Retriever is only applicable to 2-channel
sources.
Better sound using Phase Control
This receiver’s Phase Control feature uses phase correction
measures to make sure your sound source arrives at the
listening position in phase, preventing unwanted distortion
and/or coloring of the sound.
Phase Control technology provides coherent sound
reproduction through the use of phase matching for an
optimal sound image at your listening position. The default
setting is on and we recommend leaving Phase Control
switched on for all sound sources.
1 Press PHASE to switch the P.CTL (Phase Control) ON or
OFF.
Note
• Phase matching is a very important factor in achieving
proper sound reproduction. If two waveforms are ‘in
phase’, they crest and trough together, resulting in
increased amplitude, clarity and presence of the sound
signal. If a crest of a wave meets a trough, then the sound
will be ‘out of phase’ and an unreliable sound image will
be produced.
• If your subwoofer has a phase control switch, set it to the
plus (+) sign (or 0º). However, the effect you can actually
feel when Phase Control is set to ON on this receiver
depends on the type of your subwoofer. Set your
subwoofer to maximize the effect. It is also recommended
you try changing the orientation or the place of your
subwoofer.
• Set the built-in lowpass filter switch of your subwoofer to
OFF. If this cannot be done on your subwoofer, set the
cutoff frequency to a higher value.
• If the speaker distance is not properly set, you may not
have a maximized Phase Control effect.
• The Phase Control mode cannot be set to ON in the
following cases:
- When the PURE DIRECT mode is switched on.
-
When the headphones are connected.
F.S.S.ADVANCE
(Front Stage
Surround
ADVANCE)
Allows you to create natural surround
sound effects using just the front speakers
and the subwoofer.
Use to provide a rich surround sound effect
directed to the center of where the front left
and right speakers sound projection area
converges.
PHONES SURR When listening through headphones, you
can still get the effect of overall surround.
ECO MODE 1 Cut back on power consumption. Suitable
for contents that are mainly high level
(mainly music).
ECO MODE 2 Cut back on even more power consumption
than ECO MODE 1. Suitable for contents
with wider dynamic range (mainly movies).
Front left
speaker
Front right
speaker
AUTO SURROUND See Auto playback on page 26.
DIRECT Sources are heard according to the settings
made in the Manual SP Setup (speaker
setting, channel level, speaker distance), as
well as with dual mono settings. You will
hear sources according to the number of
channels in the signal.
Phase Control, Sound Delay, Auto Delay,
LFE Attenuate and Center image functions
are available.
PURE DIRECT Analog and PCM sources are heard without
any digital processing.
AUTO/
DIRECT
AUTO SURROUND/
STREAM DIRECT
GAME TV SIGNAL SEL
Acous.EQ PHASE S.RETRIEVER VOL
GAME TV SIGNAL SEL
Acous.EQ PHASE S.RETRIEVER VOL