AEG MC 4443 CD-MP3 - Manual (Page 42)

English
42
Overview of the Components
1 CD compartment
2 LCD display
3  OPEN CD compartment
4 VOLUME (volume control)
5 ALBUM button
6 II PLAY/PAUSE button
7  STOP button
8 FUNCTION Function selector switch
(OFF / CD/MP3 / RADIO)
9 AUX IN connection
10 TUNING control
11 USB connection
12 BAND Band selection switch
(AM / FM / FM ST.)
13 I SKIP+ button (reverse search)
14 I  SKIP- button (forward search)
15 MODE button (repeat/random)
16 IR Sensor for the remote control
17 FM ST. control lamp
18 POWER control lamp
Reverse Side
19 TIME SET button (time)
20 HOUR button (hours)
21 MINUTE button (minutes)
22 SPEAKERS R/L Loudspeaker connections
23 AC Mains connection
24 Power switch
25 FM ANT. throw-out aerial
26 Battery compartment (Power reserve)
Remote Control
1 II button (Play/Pause)
2 PROG button (memory)
3 I/I buttons
(reverse search/forward search)
4 ALBUM button (up album)
5 +10 button
6 MODE button (repeat/random)
7 STOP button
Intended Use
This device is used for:
• The reception of radio programmes
• Playing back audio/MP3 CDs
• Sound playback from external audio sources.
It is intended exclusively for this purpose and may only
be used as such. It may only be used in the manner
described in these instructions for use. The device must
not be used for commercial purposes.
Any other use of this device is considered to be contrary
to the intended use and may result in damage to materi-
als or even personal injury.
The firm ETV – Elektro-Technische Vertriebsgesellschaft
mbH does not accept any liability for damage caused as a
result of the use of this device contrary to its intended use.
Start-up of the device/Introduction
• Read the operating instructions thoroughly before the
start-up!
• Select an appropriate location for the device, e.g. a
dry, flat, non-slip surface on which the device can be
easily operated.
• Make sure that the device is adequately ventilated!
• Connect the loudspeakers to the back of the music
centre to the sockets market „Speaker R and L“ (22).
• Remove the protective film from the display if it is
still present.
Power Supply
• Insert the plug into a properly installed 230 V, 50 Hz
power socket.
• Please ensure that the mains voltage corresponds to
the information on the type plate.
• Turn the device on by moving the power switch (24)
to ON.
Setting the Time (in standby mode (OFF))
• Keep the TIME SET button (19) pressed down.
• Press the HOUR button (20) in order to set the hours.
Keep the button pressed down until the desired hour
is reached.
• Press the MINUTE button (21) in order to set the min-
utes. Keep the button pressed down until the desired
minutes are reached.
• The time is stored automatically.

NOTE:
The time is a 12 hour display.
AM = in the morning; PM = in the afternoon/evening.

NOTE:
Storage/display of the time is lost as soon as the
electricity supply is interrupted. If you would like
to have the time displayed even when the power is
disconnected, insert a button cell of type CR 2025
with the correct polarity in the battery compartment
(26) (battery not supplied). Open the lid of the battery
compartment on the back by turning in the direction
of OPEN.
Inserting the Batteries

NOTE:
The lithium cell in the battery compartment of the re-
mote control has been secured for transport with a foil.
This prolongs the lifetime of the battery. Before initial
use please remove this foil so that the remote control is
ready for operation.
The battery of the remote control is a long-life lithium
cell. If the range of the remote control is reduced during
use, please proceed as follows:
05-MC 4443 AEG.indd 42 14.09.2010 14:47:24 Uhr