AEG IMS 4441 - Manual (Page 32)

English
32
SLEEP (2)
When the device is switched on, you can set the time after
which the device will turn into standby mode; set the time in
10 minutes intervals from 90 to 10 minutes. Repeatedly press
this button until the display shows the desired time. When
the function is activated, the display will show the symbol
“
”.The device will turn off automatically after the preset
time.
To deactivate the function, press the SLEEP button until OFF
is shown on the display.
ALARM (6)
You can set the unit so that it switches on at a certain time.
1. Use
I/ button to switch into standby mode (time will be
displayed).
2. Keep the ALARM button pressed until the hours and the
“ ” symbol flash.
• Using the / TUNING/SKIP / buttons (13), you
can now set the turn-on hours, turn-on minutes and
turn-on mode in turn.
• Set the turn-on volume with the V�LUME +/- but-
tons.
• Confirm your input each time with the ALARM
button. The current display to be set flashes on the
display.
3. After you have selected the turn-on volume, press the
ALARM button again. “ ” will be displayed and the
timer is activated.
After the set time has been reached, the device switches to
the selected mode.
• Use the
I/ and ALARM buttons to turn off the function
until the next day. The “ ” symbol continues to be
shown on the display.
• To deactivate the timer, press the ALARM button again.
“ ” will disappear from the display.
• Snooze function
Use the MEM/CLK-ADJ. / SN��ZE button (5 and 12 on
the unit) to turn off the automatic preset timer function for
approx. 9 minutes. “SN��ZE” appears on the display.
MEM/CLK-ADJ. / SNOOZE (5)
Set the clock, store stations and program playback.
Program Playback
Program playback in desired sequence. (Only in CD mode)
1. Drücken Sie die / ST/MO Taste (4).
2. Press iP�D/MEM/CLK-ADJ. button (5). The display will
show “P01 T001” (“memory position” “Title”) and MEM
Use the buttons / TUNING/SKIP / (13) to select
the desired track and press iP�D/MEM/C-ADJ. button
again. The display will change to memory position P02.
3. Use the / TUNING/SKIP / buttons to select the
next track and press iP�D/MEM/CLK-ADJ. again. Repeat
the steps until you have selected all tracks.
4. Press the / AUT� MEM button (3). Playback starts.
The display will show the first selected track number.
5. Press / ST/MO button once to stop playback. The
memory will be kept.
6. To play the program again, press the / AUT� MEM
button.
7. To delete memory, please press / ST/MO button twice.
The MEM display switches off.
The unit does not stop automatically after all programmed
titles have been played. The program sequence will be kept
in the memory until you switch to another mode, remove the
CD from the compartment or switch off the device.
Playback of music files in MP3 format
This device allows the playback of music files in MP3 format.
The device furthermore supports the common CD types: CD,
CD-RW, and CD-R.
Your device can play MP3 CDs. These are compressed CDs
that can store up to 200 tracks. Your device automatically
recognizes MP3 discs (the display will show total number of
tracks and folders). Please refer to chapter “Playing CD/MP3”
for playback of such CDs. You may program tracks as already
described under “Program playback”.
Please note:
There are many burning and compressing methods, as well
as differences in quality of CDs and burnt CDs.
Furthermore, the music industry does not apply fixed stan-
dards (copy protection).
For that reason there might, in rare cases, occur problems
when playing CDs and MP3 discs. That is
not a malfunction
of this device.
Cleaning and maintenance
• Disconnect the mains plug before cleaning.
• You may wipe off external stains, using a slightly damp
cloth without any additives.
Trouble shooting
Problem Cause Solution
The unit cannot be
operated The unit is blocked
and “hangs” Pull the mains plug
for approximately
5 seconds. Then
connect the unit
again