AEG PW 4923 FA - Manual (Page 37)

37
eNGLIsh
Note:
Due to the significant fluctuation of body fat, it is difficult to
attain a standard value. On average the optimal testing time
is between 6 p.m. and 8 p.m, since the body fat remains very
consistent during this period of time.
First use of the Machine
Battery compartment (on the back of the scales)
Note:
The battery in the battery compartment has been secured for
transport with a foil. This prolongs the life of the battery.
Please remove this foil to prepare the scales for initial use.
use
Weighing Function
• Place the scale on a hard, flat surface (avoid carpets). An
uneven floor contributes to inaccurate measurements.
• On the back side of the scale beside the battery compart-
ment a switch can be found. Choose between the measur-
ing units “kg” and “lb” (pound).
• Turn on the scale by pressing the ON button.
• The scale and the display conduct a self-test (8888). Shortly
afterward the digits “0.0” (kg) (0.0 lb) will appear.
• Stand with both feet on the contact surfaces (6) of the
device. Distribute your weight equally and wait for the scale
to determine your weight.
• The digits on the display will flash before your exact weight
will be shown.
• In order to extend the battery life, the device will automati-
cally turn off 10 seconds after you have stepped off the
scale.
Programming Your Personal Data
Note:
► The scale has default values that you can change, as
described below.
► You should perform the following steps in order and within
a few seconds; otherwise the device aborts the program-
ming mode automatically!
• Turn the scale on by pressing the ON button.
• Always wait until the display shows the digits 0.0 kg (0.0 lb).
• Press the button SET. The memory space will flash on
the display. Confirm the setting by pressing SET or select
another memory space by pressing the UP / DOWN button.
Then press SET to go to the next setting.
• The symbol for “male” or “female” will flash. Confirm the
setting by pressing SET or use the DOWN button to choose
the symbol for your gender. Then press SET to go to the
next setting.
• The setting AGE will flash. Select your age by pressing UP
or DOWN button. Holding down one of the buttons will ac-
celerate the process. Confirm your entry by pressing SET.
• The height setting will flash. Select your height by pressing
UP or DOWN button. Holding down one of the buttons will
accelerate the process. Confirm your entry by pressing
SET.
As a confirmation you will once again see all the entered set-
tings in the memory space.
When the digits 0.0 kg (0.0 lb) appears on the display, you can:
• Press the SET button to see the selected settings again.
• Allocate further memory spaces. There are 10 spaces avail-
able in total. Press SET and change the space by pressing
the UP or DOWN button. Proceed further as described
above.
• Make changes by selecting the particular memory space
by pressing SET (the display will flash). Proceed further as
described above.
• You can immediately start measuring.
Determining Weight, Body Fat and Body Water Percentage
Record your personal data in the memory.
Note:
► The device can only function correctly if you stand on the
device with bare, dry feet!
► If necessary wipe the contact surfaces to improve results.
• Turn on the scale by pressing the ON button.
• Always wait until the digits 0.0 kg (0.0 lb) appears on the
display.
• Press the button SET. The memory space will flash on the
display. Select the memory space where your data has
been saved by pressing the UP / DOWN button. Wait until
the memory space stops flashing. It will display the saved
values one after another.
• If the display stops at 0.0 kg (0.0 lb), stand with both feet on
the contact surfaces (6) of the scale.
• First your weight will appear on the display. Afterwards the
analysis will begin. Remain standing on the scale during
this process.
• After a few seconds you will see the following information
on the display
- Your body fat percentage (Symbol )
- Your body water percentage (Symbol )
- Your muscle mass percentage (Symbol )
- Your bone weight percentage (Symbol ).
• Whilst the percentage of body fat will be displayed, an
estimated value appears on the display below. This informs
you in a glance of which range/division you are in.