Konica Minolta bizhub 20P - Manual (Page 3)

2
■ Regulations
● Federal Communications Commission (FCC) Declaration of Conformity (For USA only)
Responsible Party: KONICA MINOLTA BUSINESS SOLUTIONS U.S.A., INC.
100 Williams Drive
Ramsey, NJ 07446
Phone: 201-825-4000
declares, that the products
Product Name: Laser Printer bizhub 20P
Model number: 20P
comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
„ Reorient or relocate the receiving antenna.
„ Increase the separation between the equipment and receiver.
„ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
„ Call the dealer or an experienced radio/TV technician for help.
● Important
Changes or modifications not expressly approved by us could void the user's authority to operate the equipment.
● Important - about the interface cable
A shielded interface cable should be used to ensure compliance with the limits for a Class B digital device.
● Industry Canada Compliance Statement (For Canada only)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of this device.
● Radio interference (220-240 volt model only)
This product complies with EN55022 (CISPR Publication 22)/Class B.
● For European Users
This product complies with the following EU directives:
2004/108/EC, 2006/95/EC and 2009/125/EC
This declaration is valid for the areas of the European Union (EU) or EFTA only.
● Ozone Release
During print operation, a small quantity of ozone is released. This amount is not large enough to harm anyone adversely.
However, be sure the room where the machine is being used has adequate ventilation, especially if you are printing a high
volume of materials, or if the machine is being used continuously over a long period.
● Dégagement d’ozone
En cours de fonctionnement, l’imprimante ne dégage qu'une faible quantité d’ozone, insuffisante pour provoquer un
quelconque malaise personnel. Veillez cependant à ce que la pièce dans laquelle la machine est installée soit aérée de
manière adéquate, notamment si vous imprimez de gros volumes ou si l'imprimante est longtemps utilisée en continu.
● For EU member states only
This product complies with RoHS (2002/95/EC) directive.
● International ENERGY STAR ® Compliance Statement
The purpose of the International ENERGY STAR ® Program is to promote the development and popularization of
energy-efficient office equipment.
As an ENERGY STAR
® Partner, KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. has determined that this product
meets the ENERGY STAR ® guidelines for energy efficiency.
● Laser Safety
This equipment is certified as a Class 1 laser product as defined in IEC60825-1:2007 under the U.S. Department of Health
and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act
of 1968. This means that the equipment does not produce hazardous laser radiation.
Since radiation emitted inside the equipment is completely confined within protective housings and external covers, the laser
beam cannot escape from the machine during any phase of user operation.
● FDA Regulations
U.S. Food and Drug Administration (FDA) has implemented regulations for laser products manufactured on and after August 2,
1976. Compliance is mandatory for products marketed in the United States. The following label on the back of the equipment
indicates compliance with the FDA regulations and must be attached to laser products marketed in the United States.
COMPLIES WITH 21CFR 1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE
NO.50, DATED JUNE 24, 2007.
● IEC60825-1:2007 Specification
This machine is a Class 1 laser product as defined in IEC60825-1:2007 specifications. The label shown below is attached in
countries where required.
This machine has a Class 3B Laser Diode which emits invisible laser radiation in the
Laser Unit. The Laser Unit should not be opened under any circumstances.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
PRODUCTO LASER DE CLASE 1
WARNING
Use of controls or adjustments or performance of procedures other than those specified in this manual may result in
hazardous invisible radiation exposure.
● Internal Laser radiation
Maximum radiation power: 5 mW
Wave length: 770 - 810 nm
Laser Class: Class 3B