Konica Minolta magicolor 2500W - Manual (Page 3)

4
■Regulation Notices
●Laser Safety
This product employs a Class 3B laser diode having maximum power of 10 mW and wavelength of 775 - 800 nm.
This product is certified as a Class 1 laser product. Since the laser beam is concealed by protective housings, the product
does not emit hazardous laser radiation as long as the product is operated according to the instructions in this manual.
●Internal Laser Radiation
Maximum average radiation power: 7.5 µW at the laser aperture of the print head unit.
Wavelength: 775-800 nm
CAUTION:
Use of controls, adjustments, or performance of procedures other than those specified in this manual may result in
hazardous radiation exposure.
●Interference-Causing Equipment Standard (ICES-003 ISSUE 4)
- For Canadian Users
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device must be used with a shielded interface cable. The use of non-shielded cables is likely to result in interference with
radio communications and is prohibited under ICES-003.
●FCC Part 15 - Radio Frequency Devices
- For United States Users
FCC: Declaration of Conformity
Product Type Color Laser Printer
Product Name magicolor 2500W
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions:
• This device may not cause harmful interference, and this device must accept any interference received,
including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interface by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
WARNING:
The design and production of this unit conform to FCC regulations, and any changes or modifications must be registered
with the FCC and are subject to FCC control. Any changes made by the purchaser or user without first contacting the
manufacturer will be subject to penalty under FCC regulations.
This device must be used with a shielded interface cable.
The use of non-shielded cables is likely to result in interference with radio communications and is prohibited under FCC
rules.
●For European Users
This product complies with the following EU directives:
89/336/EEC, 73/23/EEC and 93/68/EEC
This declaration is valid for the areas of the European Union (EU) or EFTA only.
This device must be used with a shielded interface cable. The use of non-shielded cables is likely to result in interference
with radio communications and is prohibited under 89/336/EEC rules.
●Ozone Release
During print operation, a small quantity of ozone is released. This amount is not large enough to harm anyone adversely.
However, be sure the room where the machine is being used has adequate ventilation, especially if you are printing a high
volume of materials, or if the machine is being used continuously over a long period.
●Dégagement d’ozone
L’imprimante dégage une faible quantité d’ozone durant son utilisation.
Cette quantité n’est pas suffisamment importante pour être dangereuse. Cependant, veillez à ce que la pièce dans laquelle
la machine soit adéquatement ventilée, surtout en cas d’impression de gros volumes ou en cas d’utilisation continue
pendant un laps de temps très long.
●Electromagnetic Interference
This product must be used with a shielded interface cable.
The use of non-shield cables is likely to result in interference with radio communications and is prohibited under CISPR 22
and local rules.
(A00V-9562-00A)
Laser Caution Label
Laser aperture of the
print head unit.