Asus Motherboard P5SD2-X - Manual (Page 40)

1 - 2 8 1 - 2 8 1 - 2 8 1 - 2 8 1 - 2 8 C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
7 . 7 . 7 . 7 . 7 . A T X p o w e r c o n n e c t o r s ( 2 4 - p i n E A T X P W R , A T X p o w e r c o n n e c t o r s ( 2 4 - p i n E A T X P W R , A T X p o w e r c o n n e c t o r s ( 2 4 - p i n E A T X P W R , A T X p o w e r c o n n e c t o r s ( 2 4 - p i n E A T X P W R , A T X p o w e r c o n n e c t o r s ( 2 4 - p i n E A T X P W R , 8 - p i n A T X 1 2 V ) 8 - p i n A T X 1 2 V ) 8 - p i n A T X 1 2 V ) 8 - p i n A T X 1 2 V ) 8 - p i n A T X 1 2 V )
These connectors are for an ATX power supply. The plugs from the
power supply are designed to fit these connectors in only one
orientation. Find the proper orientation and push down firmly until the
connectors completely fit.
• It is recommended that you use an ATX 12 V Specification
2.0-compliant power supply unit (PSU) with a minimum of 350 W
power rating. This PSU type has 24-pin and 8-pin power plugs.
• If you intent to use a PSU with 20-pin and 4-pin power plugs, make
sure that the 20-pin power plug can provide at least 15A on +12V
and that the PSU has a minimum power rating of 350 W. The system
may become unstable or may not boot up if the power is
inadequate.
• Do not forget to connect the 8-pin ATX +12 V or 4-pin ATX +12V
power plug; otherwise, the system will not boot up.
• Use of a PSU with a higher power output is recommended when
configuring a system with more power-consuming devices. The
system may become unstable or may not boot up if the power is
inadequate.
• The ATX 12 V Specification 2.0-compliant PSU passed the
motherboard power requirement test with the following
configuration:
CPU : Intel ® Pentium ® 4 3.6 GHz
Memory : 512 MB DDR2 (x 4)
Graphics card : PCI Express x16 Nvidia EN5900
Parallel ATA devices : IDE hard disk drive (x 2)
Serial ATA device : SATA hard disk drive
Optical drives : CD-ROM (x 2)
SCSI devices : SCSI card and SCSI hard disk drive
• You must install a PSU with a higher power rating if you intend to
install additional devices.
P5SD2-X
®
P5SD2-X ATX power connectors
EATXPWR EATX12V
+3 Volts
+3 Volts
Ground
+5 Volts
+5 Volts
Ground
Ground
Power OK
+5V Standby
+12 Volts
-5 Volts
+5 Volts
+3 Volts
-12 Volts
Ground
Ground
Ground
PSON#
Ground
+5 Volts
+12 Volts
+3 Volts +5 Volts
Ground
GND +12V DC
GND +12V DC
GND +12V DC
GND +12V DC