Alpine CDA-7897 - Manual (Page 8)

6
-EN
Adjusting Volume/Balance(Between
Left and Right)/Fader (Between Front
and Rear)/Defeat
1
Press the MODE button repeatedly to choose the
desired mode.
Each press changes the modes as follows:
Volume : 0 ~ 35
Balance : L15 ~ R15
Fader : R15 ~ F15
Subwoofer: 0 ~ +15
Press the g DN or f UP button after selecting the
Subwoofer mode, and the subwoofer output phase is
toggled “NORMAL (PHASE 0
°)” or “REVERS (PHASE
180 °)”.
NOTES
• If the MODE button is not pressed within 5 seconds after
selecting the BALANCE, FADER, DEFEAT or Subwoofer
mode, the unit automatically returns to the VOLUME mode.
• When setting the 2WAY/3WAY switch (page 47) to 3WAY, you
cannot adjust the FADER mode.
•*When the subwoofer mode is OFF, its level cannot be
adjusted.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
NOTE
Depending on the connected devices, some functions and display
indications do not work.
Audio Mute Function
Activating this function will instantly lower the volume
level by 20 dB.
1
Press the MUTE button to activate the MUTE mode.
The audio level will decrease by about
20 dB.
Pressing the MUTE button again will bring the audio
back to its previous level.
Displaying Time
1
Press the CLK (clock) button repeatedly until the time
is displayed.
Each press changes the modes as follows:
Radio mode
CD mode
∗1
Displayed during playback of a disc with CD Text.
“NO TEXT” will be displayed when the CD
contains no Text data.
∗2
“NO TITLE” will be displayed when the title has
not been inputted.
NOTES
• Selecting any tuner or CD function while in the clock mode
will interrupt the time display momentarily. The function
selected will be displayed for about 5 seconds before the time
returns to the display.
• When the power is off but the ignition key is on, press the CLK
button to display the time. (CDA-7897 only)
Setting Time
1
In the Clock display mode, press and hold the CLK
(clock) button for at least 3 seconds while the time is
displayed.
< CDA-7998 only >
2
Turn the Rotary encoder to adjust the hours while the
years indication is blinking.
3
When the year has been adjusted, press MODE
button.
4
Turn the Rotary encoder to adjust the months, days,
hours and minutes while the time indication is blinking.
The time is automatically set 5 seconds after the
minute adjustment. The time can be manually set by
pressing the MODE button.
< CDA-7897 only >
2
Turn the Rotary encoder to adjust the hours while the
hours indication is blinking.
3
When the hour has been adjusted, press MODE
button.
Basic Operation
g DN
f UP Rotary encoder
EQ MUTE
SOURCE Preset buttons (1 through 6)
BAND
CLK
MODE
→ →
— — — — — — —
Elapsed Time Display
→ →
(CDA-7897 only)
←
Title Display ∗2
Elapsed Time Display
Text Display (Track Name) ∗1
Elapsed Time Display
←
Text Display (Disc Name) ∗1
Elapsed Time Display
Clock Display
Elapsed Time Display
— — — — — — —
Calendar/Clock Display
(CDA-7998 only)
→
→ →
Clock Display
Frequency Display
→
— — — — — — —
Frequency Display
— — — — — — —
Calendar/Clock Display
(CDA-7998 only)
(CDA-7897 only)
→
Title Display ∗2
Frequency Display
→ Subwoofer∗→ BALANCE → FADER
VOLUME
← DEFEAT ←