Silverline Air Nailer Stapler 32mm - Manual (Page 6)

www.silverlinetools.com
5
Air Nailer Stapler 32mm 269131
WARNING: User exposure to tool vibration can result in loss of sense of touch, numbness,
tingling and reduced ability to grip. Long term exposure can lead to a chronic condition.
If necessary limit the length of time exposed to vibration. Use the figures provided in the
specification relating to vibration if provided to calculate the duration and frequency of
operating the tool. The 2002/44/EC directive relating to vibration in the workplace may
provide useful information even for domestic use of tools. In the first instance of feeling
uncomfortable due to vibration STOP using the tool immediately.
WARNING: Always wear ear protection where the sound level exceeds 85dB(A) and
limit the time of exposure if necessary. If sound levels are uncomfortable even with ear
protection stop using the tool immediately and check the ear protection is correctly fitted
and provides the right level of sound attenuation for the level of sound produced by your
tool.
3) Tool Use and Care
a) Maintain tools. Check for misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the tool’s operation. If damaged,
have the tool repaired before use. Many accidents are caused by poorly maintained
tools.
b) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
c) Use the tool’s accessories and tool bits etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of
the tool for operations different from those intended could result in a hazardous
situation.
4) Service
a) Have your tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the tool is maintained.
Air Tool Safety
Protect your eyes
• Always wear safety goggles or safety glasses
Protect your hearing
• Always wear ear protection
Protection from vibration
• Hand-held air tools may produce vibration and should not be used for long periods
without a break. Vibration can cause ill health. Gloves may help to maintain good blood
circulation in the fingers.
Protective clothing
• Always wear appropriate protective equipment including but not limited to overalls,
gloves, face mask etc
• It is the user’s responsibility to ensure that other persons in the vicinity of the work area
are also equipped with the appropriate protective equipment
Use the correct air hose
• Use lightweight hose to connect the tool to the air compressor
• Most air tools should be fitted with a coil hose.
Always disconnect
• Ensure that your air tool has completely stopped functioning before putting it down
• Disconnect an air tool from the air supply before performing any servicing, or changing
any blades, discs, or other attachments
• Ensure blades, discs or attachments are correctly fitted before reconnecting to air
supply
• Ensure the air tool is switched OFF before connecting to air supply. Be aware that air
tools may hold residual pressure after use. Always bleed air pressure from the tool after
shutting off air supply
Do not abuse the machine
• Do not overload the machine. Allowing the machine to work at its optimum speed is
more efficient and prolongs its service life
• Do not increase air pressure above the recommended level; excessive pressure leads to
wear of moving parts, possible failure and may cause the machine casing to split
• Do not attempt to modify air tools. Any attempt to modify this air tool could result in
serious injury to you or others, and will invalidate its warranty
• Do not aim the nailer away from the workpiece when connected to an air supply
Never operate the tool with the safety mechanism disabled
• Never aim the tool towards other people in the work area or towards the main reservoir
tank of the air compressor
Do not operate the nailer when using ladders or scaffolding
• Never connect this tool to canisters or bottles containing combustible gases or portable
compressed air canisters or cartridges. It is designed to be used with an air compressor
1 Trigger
2 Quick Connector
3 Air Tool Oil
4 Magazine Latch
5 Magazine Cover
6 Safety Yoke
7 Hex Keys
8 Screws
9 Exhaust Direction Dial
Product Familiarisation
Unpacking Your Tool
• Carefully unpack and inspect your tool. Familiarise yourself with all its features and
functions.
• Ensure that all parts of the tool are present and in good condition. If any parts are
missing or damaged, have such parts replaced before attempting to use this tool.
Before Use
Installing the quick connector
• Fit the Quick Connector (2) to the nailer. The quick connector is a screw fit into the Air
Inlet. Applying PTFE tape to the screw threads will help to maintain an airtight seal. Air
lines fitted with matching ¼" connectors will now be a push fit
Recommended air supply
WARNING: Never use oxygen or other bottled gases as a power source. Explosion may
occur. Combustible gases and other bottled gases are dangerous and may cause the tool
to explode.
• This tool should be connected to a clean air supply with an in-line oiler and water
separator
• DO NOT allow supply pressure to exceed the maximum stated in the specification
• Always select the lowest supply pressure suitable for the task. This will reduce sound
and vibration for the operator. It will also decrease wear of the tool and the chance of
tool failure
• Always use an air filter with the machine. Without an air filter, air is likely to have a
higher water content that will rapidly corrode the internal working parts of this machine
and will shorten its working life significantly. Water collects in the compressor tank and
will cause serious corrosion. The tank must be drained on a daily basis to prevent water
build-up in the air supply
• Ensure all parts of the system (hoses, couplers, etc.) are correctly rated for the air
pressure to be used
• If an automatic oiler (as per diagram below) is not used, pour two drops of air tool oil
into the air inlet of the quick connector before each use
CAUTION: Only use oil formulated for air or pneumatic tools. Never substitute other oils
which may damage this tool and the compressor or are not suitable for contact with the
operator of the tool. DO NOT use 2-stroke or automotive oil.
TO YOUR
AIR TOOL
LEADER HOSE
NIPPLE
QUICK COUPLER
WATER SEPARATION
OILER
NIPPLE
REGULATOR
DRAIN DAILY
AIR SUPPLY
RECOIL HOSE
269131_Z1MANPRO1.indd 5 19/07/2013 09:09