Fagor 6H-880ATCX - Manual (Page 29)

e n g l i s h
27
1
2
Installation
Using the oven
1.1 Unpacking. Remove all the protective
packaging elements.
1.2 Mains connection. Always take into account
the data on the reference plate (1.2.1) and
the measurements of the cabinet the oven
will be housed in (1.2.2, 1.2.3).
The appliance must be connected to the
mains with a fi xed single-phase connection
with the neutral-to-neutral (blue) connection
guaranteed (1.2.4). Fit the oven into the
space and centre it (1.2.5). Make sure there
is no excess cable in the upper part (1.2.6).
Screw it to the fi tting using the two screws
supplied (1.2.7). The fi tted furniture or its
surface must be heat-resistant. The time
must be set in order to fi nish the installation.
After a period of inactivity, the machine
will turn to standby and its brightness
will diminish or the screen will switch off,
depending on the model.
Before using your new oven for the fi rst time,
heat it up while empty (with no food in it and with the
control turned to
, for 30 minutes at 250ºC). It may
produce some smoke or a bad smell (this is normal and
is caused by the oven heating up grease residue etc.).
When it has cooled down, pre-clean it by wiping the
inside with a damp cloth.
You may browse the oven menu display and confi gure
it as you wish and/or use the different buttons for
cooking.
On/cancel. , Browse the different
menu options. Validate an option. Return to
previous display. Block oven keypad.
2.1 Accessories. Depending on the model
there is a Deep Tray (2.1.1), Flat Tray (2.1.2)
and Multifunctional Grill (2.1.3) that work
separately. If it also possible to combine
either tray with the Multifunctional Grill
(2.1.4) to make a set. All the accessories
or sets can be used directly or mounted
on the Partial Extraction Grill (2.1.5) or the
Total Extraction Grill (2.1.6, 2.1.7), (2.1.8).
If you have the partial extraction tray, it can
be used separately or together with trays
(3 types) (2.1.9). The Simple Grill is used
separately (2.1.10). If you have telescopic
rails, remove the tray before installing them in
the oven (2.1.11). The telescopic rails extend
automatically due to the weight of the tray
when the oven is opened (2.1.12). Food must
always be placed on a tray on the telescopic
rails (2.1.13). Bear in mind the position of
the grills when installing them. There are
anti-tipping stops at the sides (2.1.14). The
low temperature grill is required to use the “low
temperature cooking” mode (2.1.15).
2.2 Accessory positions. The accessories
can be fi tted in 5 different positions
.
2.3 Selecting a language. When you switch on the
oven for the fi rst time or when the electricity returns
after a power cut, the language selection display
will appear. Press
or until the desired
language is highlighted and press to validate
(2.3.1).
2.4 Adjusting the time and date. After the language
has been validated, the date and time adjustment
display will appear (2.4.1). Press
or until
the Time appears (2.4.2). Validate by pressing
. The time will fl ash (2.4.3). Press or to
change the time (2.4.4). After adjusting the time,
press
to validate (2.4.5). Repeat the same
sequence to adjust the date and the 12/24 hour
mode. When all these items have been set, press
to validate (2.4.6).
Note: You may choose to view the clock in
analogue (2.4.7) or digital (2.4.8) mode.
2.5 Changing the language. Press . TAfter the
starting animation, the menu display will appear
(2.5.1). Press
, until Settings appears,
and press to validate (2.5.2). Press ,
to select the Language and press to validate
(2.5.3). Follow the sequence to change the
language (2.3.1).
2.6 Changing the time and date. Select Settings
and validate (2.5.1, 2.5.2). Press , to
select the Time / Date. Press to validate
(2.6.1). Follow the sequence to change the time
(2.4.1 - 2.4.6).
2.7 Beeper function. Press to access the menu
(2.5.1). Press , to select the Minute
minder. Press to validate (2.7.1). Press ,
to enter the time. Press to validate (2.7.2).
The time will start to count down and when it
reaches zero a beep will sound. Press
to stop
the beep.
2.8 Button sound adjustment. Select Settings and
validate (2.5.1, 2.5.2). Select Sound and validate
(2.8.1). Select the Bip on or Bip off option.
Validate (2.8.2).