Balboa Water Group ColorGlo LED Multi-Color Bath Lights User Manual
Colorglo ™ led multi-color bath lights, Danger, Risk of electrical shock or electrocution

40663 Rev A July 28, 2009
ColorGlo
™ LED Multi-Color Bath Lights
DANGER
Risk of Electrical Shock or
Electrocution
Always disconnect power to the bath light
at the circuit breaker before servicing the
light. Failure to do so could result in death or
serious injury to the installer, bath users, or
others due to electrical shock.
Choosing Lighting Modes
The ColorGlo™ LED Multi-Color
Bath Light comes pre-programmed
with 10 exciting lighting modes.
To advance to the next lighting
UÊ
mode, switch the unit off
and then on again within five
seconds.
To resume a lighting mode,
UÊ
leave the unit switched off to
store the last lighting mode
displayed in memory. That
same lighting mode will
display the next time the unit is
switched on.
Safety Precautions
Be sure to follow all instructions
UÊ
in this user guide and carefully
observe all safety precautions.
Do not attempt to service
UÊ
the electronic components
yourself. Non-expert handling
may cause injury to the user
and/or damage the unit. Any
opening, altering or tampering
with this product will void the
manufacturer’s warranty.
Do not submerge this unit in
UÊ
water or allow it to get wet.
Keep the unit dry at all times.
Do not allow this unit to freeze.
UÊ
Always handle this unit
UÊ
cautiously, being careful to
never drop it.
www.ColorGloProducts.com
ColorGlo™ LED Multi-Color Bath Light offers
a variety of microprocessor controlled lighting
effects that will instantly transform your bath
into a color-rich paradise.
This user guide contains important information
regarding the operation of your LED Bath Light.
Please review the entire guide carefully and save it
for future reference.
Replacing the LED Bath Light and or
Standard 12 Watt Light Bulb
Step 1
Access the currently installed
light/s by removing the center,
clear light lens. Use the tool
provided with your whirlpool to
remove this center lens.
Step 2
Remove the o-ring seal very
carefully. Make sure not to
stretch the o-ring.
Step 3
Remove the light bulb or LED
from the socket in the rear light
reflector housing. To remove
bulb, pull it straight back
towards you.
Do not twist to
remove.
Step 4
Plug the bulb or LED Bath
Light into the socket. Push
the blade connection firmly
into the socket in the reverse
manner to which you removed
the bulb. Make sure the bulb or
LED light is securely installed or
bottomed out.
Step 5
Replace the o-ring very carefully
and reinstall the center light
lens using the same tool you
used to remove it.
Note: Make sure not to over
tighten, crimp or distort the
o-ring when reinstalling the
center light
lens. (See Safety
Precautions)
Operating the LED ColorGlo™
Multi-Color Bath Light
The LED Bath Light is easily
controlled using the bath existing
light switch to turn the unit on and
off.
Lighting Mode Sequence
Magenta
UÊ
Blue
UÊ
Red
UÊ
White
UÊ
Sunburst
UÊ
Green
UÊ
Tidal Wave
UÊ
Afterburner Fade
UÊ
Color Burst
UÊ
Slow Dance
UÊ
LED Life Rating
Light Emitting Diodes (LEDs)
generate the illumination of the
Bath Light.
The predicted source life of the LED
is rated at 100,000 elapsed time
hours, or 11 years of continuous use,
under normal operating conditions.
The following are considered normal
operating conditions for this multi-
color bath light:
Temperature range of -4° F to
UÊ
104°F (-20°C to 40°C )
Humidity range of 0% - 95%,
UÊ
non-condensing