Panasonic SC-HC38 - Manual (Page 12)

12
RQT9742
Stations cannot be selected.
Change the FM frequency step.
1 Press [RADIO] to select “FM”.
2 Press and hold [SELECTOR] on the unit.
After a few seconds the display changes to show the
current lowest frequency. Continue to hold the button
down. The lowest frequency changes and the step is
changed.
Cannot charge or operate.
≥ Have you selected the appropriate selector?
Press [iPod] to select either “IPOD_DOCK” or
“IPOD_PORT”.
≥ Check that the iPod/iPhone/iPad is connected properly.
( l 6)
≥ The battery of the iPod/iPhone/iPad is depleted. Charge
the iPod/iPhone/iPad, and then operate again.
≥ Connect the iPod/iPhone/iPad again or try to restart the
iPod/iPhone/iPad.
≥ When this unit is in standby mode, charging will not start
when using the “IPOD_PORT” connection.
Turn this unit on and make sure the charging has started
before switching this unit to standby mode.
Pairing cannot be done.
≥ Check the Bluetooth ® device condition.
The device cannot be connected.
≥ The pairing of the device was unsuccessful or the
registration has been replaced. Try pairing the device
again. (
l 7)
≥ This unit might be connected to a different device.
Disconnect the other device and try pairing the device
again. (
l 7)
The device is connected but audio cannot be
heard through this unit.
≥ For some built-in Bluetooth ® devices, you have to set the
audio output to “SC-HC38” manually. Read the operating
instructions for the device for details.
The sound is interrupted.
≥ The device is out of the 10 m (33 ft) communication
range. Bring the Bluetooth ® device closer to this unit.
≥ Remove any obstacle between this unit and the device.
≥ Other devices that use the 2.4 GHz frequency band
(wireless router, microwaves, cordless phones, etc.) are
interfering. Bring the Bluetooth
® device closer to this unit
and distance it from the other devices.
≥ Select “MODE1” for stable communication. ( l 7)
The remote control doesn't work properly.
≥ The remote control and this unit are using a different
code. ( l 13, “REMOTE ”)
≥ Is the battery depleted or is the battery inserted
incorrectly? ( l 4)
The following messages or service numbers
may appear on the unit's display.
“--:--”
≥ You plugged the AC power supply cord in for the first
time or there was a power failure recently. Set the time
(
l 10).
“ADJUST CLOCK”
≥ Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
≥ Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”
≥ The unit has been left unused for about 30 minutes and
will shut down within a minute. Press any button to
cancel it.
“CANNOT SET”
≥ Select an audio source other than “BLUETOOTH”.
“CHECKING CONNECTION”
≥ The unit is checking the connected iPod/iPhone/iPad.
≥ If this display keeps appearing, make sure that the
battery of the iPod/iPhone/iPad is not depleted and that
the iPod/iPhone/iPad is turned on and connected
correctly. (
l 6)
“DIMMER”
≥ Appears 10 seconds after the volume is turned to “0”.
“ERROR”
≥ Incorrect operation is performed. Read the instructions
and try again.
“F ” (“ ” stands for a number.)
≥ There is a problem with this unit.
Note down the displayed number, disconnect the
AC power supply cord and consult your dealer.
iPod/iPhone/iPad operations
Bluetooth ®
Remote control
Messages
SC-HC38~RQT9742.book Page 12 Tuesday, December 11, 2012 2:20 PM