beautypg.com

Sony CDX-MP30 User Manual

Fm/am compact disc player, 12 a b, Cdx-mp30

background image

Installation/Connections

Installation/Connexions

Instalación/Conexiones

Sony Corporation © 2002

Printed in Korea

CDX-MP30

FM/AM
Compact Disc
Player

3-241-295-21

(1)

1

TOP

Ч

4

Ч

2

2

3

4

5

Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Equipo utilizado en las ilustraciones (no suministrado)

Rear speaker
Haut-parleur arrière
Altavoz trasero

Front speaker
Haut-parleur frontal
Altavoz delantero

Cautions

• This unit is designed for negative ground 12 V

DC operation only.

• Do not get the wires under a screw, or caught

in moving parts (e.g. seat railing).

• Before making connections, turn the car

ignition off to avoid short circuits.

• Connect the yellow and red power input leads

only after all other leads have been connected.

Run all ground wires to a common ground

point.

• Be sure to insulate any loose unconnected

wires with electrical tape for safety.

• The use of optical instruments with this

product will increase eye hazard.

Notes on the power supply cord (yellow)
• When connecting this unit in combination with

other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.

• When no car circuits are rated high enough,

connect the unit directly to the battery.

Parts Iist (1)

The numbers in the list are keyed to those in the
instructions.

Caution

Handle the bracket 1 carefully to avoid injuring
your fingers.

Connection example (2)

Notes (2-B)
• Be sure to connect the ground cord before

connecting the amplifier.

• If you connect an optional power amplifier and do

not use the built-in amplifier, the beep sound will
be deactivated.

1

2

A

B

Connection diagram (3)

1

To a metal surface of the car
First connect the black ground lead, then connect
the yellow and red power input leads.

2

To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is

no power antenna or antenna booster, or with a
manually-operated telescopic antenna.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control and
power supply leads.”

3

To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.

4

To the interface cable of a car telephone

5 To the +12 V power terminal which is energised

in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the

+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black ground to it first.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control and
power supply leads.”

6

To the +12 V power terminal which is energised
at all times
Be sure to connect the black ground lead to it
first.

Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12

V DC when you turn on the tuner.

• When your car has built-in FM/AM antenna in the

rear/side glass, connect the power antenna control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing antenna
booster. For details, consult your dealer.

• A power antenna without relay box cannot be used

with this unit.

Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.

Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and

with adequate power handling capacities to avoid
its damage.

• Do not connect the speaker terminals to the car

chassis, or connect the terminals of the right
speakers with those of the left speaker.

• Do not connect the ground lead of this unit to the

negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active

speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.

• To avoid a malfunction, do not use the built-in

speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.

• Do not connect the unit’s speaker cords to each

other.

Rotary commander RM-X4S
Satellite de commande
RM-X4S
Mando rotativo RM-X4S

Power amplifier
Amplificateur de puissance
Amplificador de potencia

CD/MD changer
Changeur de CD/MD
Cambiador de CD/MD

AUDIO OUT REAR

AUDIO OUT FRONT

BUS AUDIO IN

BUS CONTROL IN

BUS AUDIO IN

BUS CONTROL IN

TOP

* not supplied

non fourni
no suministrado

Source selector

*

Sélecteur de source
Selector de fuente