Karcher KMR 1250 Lpg - Manual (Page 20)

- 5
ṇ
Warning
Do not use a forklift truck to unload the ma-
chine as this may damage it.
To unload the machine, proceed as follows:
Î
Loosen the wooden plank from the pal-
let and fit it with nails at the ends of the
palette (front side of the device).
Î Remove the elastic tape fasteners at
the stop points.
Î Knock off the locking blocks and use
them to support the wooden planks on
the left and right.
Î Slide the machine over the prepared
ramp from the pallet.
Î Loosen the rope fastened at the side-
brush frame for transportation.
The machine can be moved in 2 ways:
(1) By pushing it (see Moving sweeper
without engaging self-propulsion).
(2) By driving it (see Moving sweeper by
engaging self-propulsion).
ƽ
Danger
Risk of injury! Before engaging the free-
wheel operation, the machine must be se-
cured to prevent it rolling away.
Î
Lock parking brake.
Î Open the device hood.
Î Set the freewheel lever to OFF.
This blocks the travel drive function.
Î
Close cover.
Î Release parking brake.
The machine can now be pushed.
Note
Do not move the machine for long distanc-
es without engaging self-propulsion, a
speed of 10 km/h should not be exceeded.
Î Lock parking brake.
Î Open the device hood.
Î Set the freewheel lever to ON.
The travel drive is now ready for operation.
Î
Close cover.
Î Release parking brake.
The appliance can now be driven.
Î Park the sweeper on an even surface.
Î Remove ignition key.
Î Lock parking brake.
ƽ
Danger
Risk of explosion!
– Only use the fuels specified in the Op-
erations Manual.
– Do not refuel the machine in enclosed
spaces.
– Smoking and naked flames are strictly
prohibited.
– Ensure that no fuel reaches the hot
open surfaces.
Î Switch off engine.
Î Open the device hood.
Î Open fuel filler cap.
Î Use "regular unleaded petrol".
Î Fill tank to max. 1 cm below the lower
edge of the filler nozzle.
Î Wipe off any spilt fuel and close fuel fill-
er cap.
Î Close cover.
Note
The machine can be operated for a maxi-
mum of 3 hours on a full tank.
Î Check engine oil level.
Î Check the hydraulic oil level.
Î Empty waste container.
Î Check roller brush.
Î Check tyre pressure.
Î Shake off dust filter.
Note
For description, see section on Care and
maintenance.
Î Hang-out the rod for the leveling equipment.
Î Loosen the 4 fastening screws.
Î Bring the seat to the desired position.
Î Tighten the fastening screws and hang
in the frame again.
Note
The machine is equipped with a seat con-
tact switch If the driver's seat is vacated,
the machine is switched off.
Î Open the device hood.
Î Push lever in "ON" direction.
Î Close cover.
Î Sit on the driver's seat.
Î Accelerator pedal in zero position.
Î Lock parking brake.
Î Bring the engine speed setting to central
position (operating speed).
Î Pull out the choke.
Î Insert the ignition key into the ignition lock.
Î Turn ignition key past position 1.
Î If the machine starts, release the igni-
tion key.
Î Push in the choke again.
Note
Never operate the starter motor for longer
than 10 seconds. Wait at least 10 seconds
before operating the starter motor again.
Before Startup
Unloading
Moving sweeper without engaging
self-propulsion
Moving sweeper by engaging
self-propulsion
Start up
General notes
Refuelling
Inspection and maintenance work
Operation
Adjusting driver's seat
Starting the machine
Open fuel cock
Turning on the Appliance
20 EN